12864图文菜单时间温度控制系统（128*64LCD+ds1302+ds18b20）

ID:140725 · 发表于 2017-3-5 23:16

完整代码下载：

时间温度控制系统源代码.zip (225.76 KB, 下载次数: 97)

2017-3-5 23:15 上传

点击文件名下载附件

原理图：

时间温度控制系统原理图及元器件.pdf (312.48 KB, 下载次数: 58)

2017-3-5 23:15 上传

点击文件名下载附件

源程序部分内容预览：

/**************************************************************************************
程序名称：
时间温度控制系统（128*64LCD+ds1302+ds18b20）
主要功能：
温度计时钟闹铃密码锁篮球器计算器温度控制键盘锁系统设置等。
主要说明：
程序全部定义在一个C文件中。
作者：
JZHG
时间：
12.19
版本：
JZHG-V1.0
/**************************************************************************************/
#include<reg52.h>
#include<intrins.h>
#define uchar unsigned char
#define uint unsigned int
#define time_count 0x3cb0 //时间计数
#define close 1 //开始标志
#define open 0 //结束标志
#define keyboard P1 //键盘数据口
/*****************状态控制及温感器总线定义*****************************/
sbit b20_io=P0^0; //ds18b20总线
sbit pw_oc=P0^4; //密码锁开启控制灯
sbit buzzer=P0^5; //喇叭端口
sbit lcd_bl=P0^6; //背光控制端口
sbit als_th=P3^6; //上限温度警报
sbit als_tl=P3^7; //下限温度警报
/******************LCD12864定义**************************/
#define lcd_data P2//lcd数据口
#define comm 0 //lcd指令
#define dat 1 //lcd数据
sbit lcd_rst=P0^7; //lcd复位
sbit lcd_e =P3^0; //lcd使能
sbit lcd_rw =P3^1; //lcd读写
sbit lcd_rs =P3^2; //lcd数据指令
sbit busy =P2^7; //忙碌位
/*****************ds1302定义**************************/
sbit d02_rst =P0^1; //ds1302使能
sbit d02_data=P0^2; //ds1302数据
sbit d02_sclk=P0^3; //ds1302时钟
#define d02_wrc 0x8e //ds1302读写控制
#define d02_year 0x8c //年
#define d02_weeks 0x8a //星期
#define d02_month 0x88 //月
#define d02_day 0x86 //日
#define d02_hour 0x84 //时
#define d02_minute 0x82 //分
#define d02_second 0x80 //秒
#define d02_signs 0xc0 //系统状态（记录设计标记）
#define d02_passw 0xc2 //密码寄存器首位（有3位下位地址加2，初始值为741456）
#define d02_alm 0xc8 //闹铃时间小时位（下位为分钟下位加2）
#define d02_temp 0xcc //温度上限警报（有两位下位加2）
#define d02_initsi 0xd4 //1302初始化标志（为0xb4,说明已经初始化）
#define ret_ds1302() d02_rst=0;d02_sclk=0;d02_rst=1 //1302读写复位
#define end_ds1302() d02_sclk=1;d02_rst=0 //1302读写结束
/*================================= 全局变量定义 ==================================*/
typedef struct // 定义时间类型
{
uchar hour;
uchar minute;
uchar second;
}time;
typedef struct // 定义日期类型
{
uchar year;
uchar month;
uchar day;
uchar week;
}date;
typedef union // 定义温度类型
{
int temp_data;
uchar t_data[2];
}trdata;
trdata bdata temp; // 温度警报值暂存
date idata today={'8',1,1,1}; // 日期暂存
time idata now={0x12,0,0} , save_time={0x12,0,0};
// 时间暂存(now是读出时间暂存 save_time上一时间暂存)
uchar idata time_tick=20,time_tick1=20,alarm_time[2],als_temp[2],
// T0中断数, T1中断数, 闹铃时间, 警报温度
bl_delay=15,temp_delay=5,opera[2][12],resu[12],
// 背光时间, 温度更新时间, 计算器数据寄存, 结果寄存
i,j,save1,temp_min=0;
// 计算器i/j下标，中间暂存,温度更新（分）
uchar bdata signs=0; // 系统标记寄存器
sbit bl1=signs^7; // bl1,bl0背光选择位(00 延时,01 常开,10 关闭)
sbit bl0=signs^6;
sbit di1=signs^5; // di1,di0显示模式(00模式1,01模式2,10模式3)
sbit di0=signs^4;
sbit meu=signs^3; // 菜单显示方式(0 图片,1 文字)
sbit keb=signs^2; // 键盘锁(0 无锁,1加锁)
sbit alm=signs^1; // 闹钟启动位(0 关闭,1开启)
sbit als=signs^0; // 报警启动位(0 启动,1关闭)
uint bdata run_signs=0; // 运行标记寄存器
sbit ds18b20=run_signs^0; // 温感器存在标记(0不存在，1存在)
sbit temp_pn=run_signs^1; // 温度正负号标记(0正，1负)
sbit temprun=run_signs^2; // 温感器运行标记(0否，1启动)
sbit nba_tim=run_signs^3; // 篮球计时器标记(0关闭，1启动)
sbit adju_si=run_signs^4; // 数字更改连续标记(1连续)
sbit cal_del=run_signs^5; // 计算器显示点标记（0没有显示）
sbit cal_run=run_signs^6; // 计算完毕标记（1有效）
sbit oth_run=run_signs^7; // 其他标记
sbit alm_run=run_signs^8; // 闹钟时间到达标记（1有效）
sbit dis_sig=run_signs^9; // 显示时间标记（1有效）
sbit lock_op=run_signs^10; // 关锁时间到标记（1有效）
sbit b20time=run_signs^11; // 温感器重新读温度标记(1有效)
sbit t0_isr =run_signs^12; // TO中断标记（1有效(1s)
sbit thl_als=run_signs^13; // 温度警报标记
sbit init_d2=run_signs^14; // 模式2初始显示
sbit buzstop=run_signs^15; // 蜂鸣器停止标记
/*================================= 字体显示代码 ==================================*/
uchar code weeks[7][2]={"一","二","三","四","五","六","日"}; // 星期 //图片中文
uchar code menu_cn[6][8]={"调整","工具","设置","保密","版本","退出"};
uchar code menu_cn_2[6][6]={"调整","工具","设置","保密","版本","退出"};// 菜单文字
uchar code selected[2][16]={{"进入【】\x04 "},{"设置【】\x10 \x04 "}}; // 选框
uchar code secrets_menu[4][6]={"开锁","更改","初始化","退出"}; // 保密菜单中文
uchar code tool_menu[5][6]={"计算器","温度计","闹铃","篮球器","退出"}; // 工具菜单中文
uchar code char_num[10]={"0123456789"}; // 数字显示代码 // 每月天数
uchar code dayofmonth[12]={0x31,0x28,0x31,0x30,0x31,0x30,0x31,0x31,0x30,0x31,0x30,0x31};
uchar code key_code[]={0xD7,0x7E,0x7D,0x7B,0xBE,0xBD,0xBB,0xDE,0xDD,0xDB,0xB7,0x77,0xEE,0xED,0xEB,0xE7};
uchar code ksp[4]={0x7F,0xBF,0xDF,0xEF}; // 按键扫描代码
uchar code tool_cal[4][2]={"+ ","- ","* ","/ "}; // 运算符号
uchar code alm_sign[2][2]={"关","开"}; // 闹铃开关
uchar code set_bl_dm[2][3][4]={{"30秒","常开","关闭"},{"模01","模02","模03"}};
uchar code set_mka[3][2][4]={{"图片","文字"},{"解锁","加锁"},{"开启","关闭"}};
uchar code nba_oppo[8][2]={"红","白","蓝","绿","紫","灰","黄","黑"};
uchar code set_menu[6][4]={"背光","显示","菜单","键盘","警报","退出"};
uchar code version[9][16]={ // 版本信息
{"湖南科技经贸学院"},
{"电子信息工程学院"},
{"11年电子技能大赛"},
{" —10电子01班"},
{"作者：蒋志高 "},
{"版本：JZHG-V1.0 "},
{" 2011/12/19 "},
{"谢谢你的使用！ "},
{" (ok)\x10"},
};
uchar code timer_tips[12][16]={ // 篮球器使用说明
{"使用方法： "},
{" (+)(-)与(*)(/)"},
{"分别是两方的分数"},
{"加与减,(7)键回退"},
{"一秒,(8)键24秒复"},
{"位,(9)键暂停与开"},
{"始；暂停状态下："},
{"按两次(OK)键可返"},
{"回时钟模式-2界面"},
{"，(OK)键返回程序"},
{"界面,(./S)键两次"},
{"退出程序. \x1f"}};
/*================================= 操作导航代码 ==================================*/
typedef struct // 定义主菜单操作索引
{
uchar shaft_num;
uchar left_num;
uchar right_num;
}menu_index;
typedef struct // 定义导航更改索引
{
uchar lnum;
uchar rnum;
}index;
menu_index code index_m[6]={{3,5,1},{4,0,2},{5,1,3},{0,2,4},{1,3,5},{2,4,0}}; // 菜单导航
index code index_t[6]={{4,1},{0,2},{1,3},{2,4},{3,0}}; // 工具导航
index code index_p[5]={{3,1},{0,2},{1,3},{2,0}}; // 保密导航
index code index_s[6]={{5,1},{0,2},{1,3},{2,4},{3,5},{4,0}}; // 设置导航
index code index_a[7]={{0x81,0x91},{0x83,0x91},{0x85,0x91},{0x89,0x81},
{0x8b,0x81},{0x8d,0x81},{0x8f,0x91}}; // 调整下的坐标
index code index_temp_set[3]={{0x8b,0x81},{0x8b,0x91},{0x8f,0x91}}; // 温度设定下的坐标
index code index_alm[3]={{0x8c,0x81},{0x8e,0x81},{0x8f,0x91}}; // 闹铃更改坐标
index code index_cal[3]={{0x86,0x90},{0x8e,0x80},{0x8e,0x90}}; // 计算器操作坐标
uchar code index_nba[4]={0x93,0x97,0x8b,0x8f}; // 篮球器设置导航
/*========================== 菜单图片（宽度x高度=32*24）=============================*/
uchar code menu_pic[6][96]={
{// 调整
0x00,0x00,0x00,0x00,0x7F,0xFF,0xFF,0xFE,0x40,0x00,0x00,0x02,0x40,0x00,0x00,0x02,
0x40,0x00,0x00,0x82,0x47,0xFF,0xE1,0xC2,0x47,0xFF,0xF3,0xE2,0x47,0x38,0x68,0x02,
0x46,0xDF,0x68,0x82,0x46,0xDF,0x69,0xC2,0x46,0xDE,0xE8,0x82,0x46,0xDD,0xE8,0x02,
0x46,0xDD,0xE8,0x02,0x47,0x3D,0xE8,0x02,0x47,0xFF,0xE8,0x02,0x47,0xFF,0xE9,0xC2,
0x42,0x00,0x18,0x02,0x41,0xFF,0xF3,0xE2,0x40,0x00,0x01,0xC2,0x40,0x00,0x00,0x82,
0x40,0x00,0x00,0x02,0x40,0x00,0x00,0x02,0x7F,0xFF,0xFF,0xFE,0x00,0x00,0x00,0x00},
{// 工具
0x00,0x00,0x00,0x00,0x7F,0xFF,0xFF,0xFE,0x40,0x00,0x00,0x02,0x40,0x00,0x03,0x82,
0x41,0xF0,0x07,0xC2,0x43,0xFF,0xCF,0xE2,0x47,0x3F,0xFE,0x02,0x47,0x3F,0xFE,0x02,
0x43,0xFF,0xCF,0xE2,0x41,0xF0,0x0F,0xC2,0x40,0x00,0x03,0x82,0x40,0x00,0x00,0x02,
0x40,0x00,0x03,0xC2,0x40,0x00,0x03,0xC2,0x41,0x80,0x01,0x82,0x43,0xFF,0xF3,0xC2,
0x47,0xFF,0xFF,0xE2,0x47,0xFF,0xFF,0xE2,0x43,0xFF,0xF3,0xC2,0x41,0x80,0x01,0x82,
0x40,0x00,0x01,0x82,0x40,0x00,0x00,0x02,0x7F,0xFF,0xFF,0xFE,0x00,0x00,0x00,0x00},
{// 设置
0x00,0x00,0x00,0x00,0x7F,0xFF,0xFF,0xFE,0x40,0x00,0x00,0x02,0x43,0x18,0x00,0x02,
0x44,0xA4,0x0E,0x02,0x44,0xA4,0x1F,0x02,0x43,0x24,0x3F,0x02,0x40,0x00,0x7F,0x02,
0x40,0xF0,0xFC,0x02,0x43,0xF9,0xF0,0x02,0x43,0x03,0xE0,0x02,0x46,0x77,0x80,0x02,
0x46,0x7F,0x00,0x02,0x46,0x7E,0x00,0x02,0x46,0x7C,0x00,0x02,0x47,0x3D,0x00,0x02,
0x43,0x1D,0x81,0x22,0x43,0x81,0xB2,0x42,0x41,0xC3,0x4F,0xE2,0x40,0xFE,0x4A,0x42,
0x40,0x3C,0x32,0x42,0x40,0x00,0x00,0x02,0x7F,0xFF,0xFF,0xFE,0x00,0x00,0x00,0x00},
{// 保密
0x00,0x00,0x00,0x00,0x7F,0xFF,0xFF,0xFE,0x40,0x00,0x00,0x02,0x40,0xFC,0x03,0x02,
0x41,0xFE,0x1F,0x02,0x43,0x87,0x03,0x82,0x43,0x03,0x03,0x02,0x43,0x03,0x03,0x02,
0x43,0x03,0x0F,0x02,0x43,0x03,0x03,0x02,0x43,0x03,0x03,0x02,0x47,0xFF,0x83,0x02,
0x47,0xFF,0x83,0x02,0x47,0xCF,0x83,0x02,0x47,0x87,0x83,0x02,0x47,0xCF,0x83,0x02,
0x47,0xCF,0x87,0x82,0x47,0xCF,0x8F,0xC2,0x47,0xCF,0x9C,0xE2,0x47,0xFF,0x8F,0xC2,
0x43,0xFF,0x07,0x82,0x40,0x00,0x00,0x02,0x7F,0xFF,0xFF,0xFE,0x00,0x00,0x00,0x00},
{// 版本
0x00,0x00,0x00,0x00,0x7F,0xFF,0xFF,0xFE,0x40,0x00,0x00,0x02,0x40,0x00,0x00,0x02,
0x40,0x0F,0x00,0x62,0x40,0x1D,0x80,0xF2,0x40,0x38,0x41,0xF2,0x40,0x70,0x23,0xE2,
0x40,0xE2,0x17,0xC2,0x41,0xE4,0x4F,0x82,0x41,0xF0,0x9F,0x02,0x41,0x59,0x16,0x02,
0x42,0x4C,0x1D,0x02,0x42,0x46,0x20,0x82,0x42,0x47,0x00,0x42,0x44,0x43,0x80,0xC2,
0x44,0x44,0xC1,0xC2,0x44,0xC8,0x63,0x82,0x45,0x50,0x37,0x02,0x46,0x60,0x1E,0x02,
0x40,0x40,0x0C,0x02,0x40,0x00,0x00,0x02,0x7F,0xFF,0xFF,0xFE,0x00,0x00,0x00,0x00},
{// 退出
0x00,0x00,0x00,0x00,0x7F,0xFF,0xFF,0xFE,0x40,0x00,0x00,0x02,0x40,0x40,0xFF,0xE2,
0x40,0x60,0x80,0x62,0x43,0xF0,0x80,0xA2,0x43,0xF0,0x81,0x22,0x40,0x60,0x82,0x22,
0x40,0x40,0x84,0x22,0x40,0x00,0x88,0x22,0x40,0x00,0x88,0x22,0x47,0xFF,0xF8,0x22,
0x47,0xFF,0xF8,0x22,0x46,0x2A,0x2A,0x22,0x46,0xE3,0x78,0x22,0x46,0x77,0x78,0x22,
0x46,0xE3,0x78,0x62,0x46,0x2A,0x38,0x82,0x47,0xFF,0xF9,0x02,0x47,0xFF,0xFA,0x02,
0x40,0x00,0x0C,0x02,0x40,0x00,0x00,0x02,0x7F,0xFF,0xFF,0xFE,0x00,0x00,0x00,0x00,}};
/*================ 显示模式2数字及温度符号图片（宽度x高度=16*32）=====================*/
uchar code mode_2num[11][64]={
{// 图片数字0
0x00,0x00,0x3F,0xFC,0x5F,0xFA,0x6F,0xF6,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,
0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x60,0x06,0x40,0x02,0x00,0x00,
0x40,0x02,0x60,0x06,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,
0x70,0x0E,0x70,0x0E,0x70,0x0E,0x6F,0xF6,0x5F,0xFA,0x3F,0xFC,0x00,0x00,0x00,0x00},
{// 图片数字1
0x00,0x00,0x00,0x20,0x00,0x60,0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0xE0,
0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0x60,0x00,0x20,0x00,0x00,0x00,0x20,
0x00,0x60,0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0xE0,
0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0x60,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00},
{// 图片数字2
0x00,0x00,0x3F,0xFC,0x1F,0xFA,0x0F,0xF6,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,
0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x06,0x1F,0xFA,0x3F,0xFC,
0x5F,0xF8,0x60,0x00,0x70,0x00,0x70,0x00,0x70,0x00,0x70,0x00,0x70,0x00,0x70,0x00,
0x70,0x00,0x70,0x00,0x70,0x00,0x6F,0xF8,0x5F,0xFC,0x3F,0xFE,0x00,0x00,0x00,0x00},
{// 图片数字3
0x00,0x00,0x7F,0xFC,0x3F,0xFA,0x1F,0xF6,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,
0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x06,0x1F,0xFA,0x3F,0xFC,
0x1F,0xFA,0x00,0x06,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,
0x00,0x0E,0x00,0x0E,0x00,0x0E,0x1F,0xF6,0x3F,0xFA,0x7F,0xFC,0x00,0x00,0x00,0x00},
{// 图片数字4
0x00,0x00,0x40,0x02,0x60,0x06,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,
0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x60,0x06,0x5F,0xFA,0x3F,0xFC,
0x1F,0xFA,0x00,0x06,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,
0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x06,0x00,0x02,0x00,0x00,0x00,0x00},
{// 图片数字5
0x00,0x00,0x3F,0xFC,0x5F,0xF8,0x6F,0xF0,0x70,0x00,0x70,0x00,0x70,0x00,0x70,0x00,
0x70,0x00,0x70,0x00,0x70,0x00,0x70,0x00,0x70,0x00,0x60,0x00,0x5F,0xF8,0x3F,0xFC,
0x1F,0xFA,0x00,0x06,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,
0x00,0x0E,0x00,0x0E,0x00,0x0E,0x0F,0xF6,0x1F,0xFA,0x3F,0xFC,0x00,0x00,0x00,0x00},
{// 图片数字6
0x00,0x00,0x3F,0xFC,0x5F,0xF8,0x6F,0xF0,0x70,0x00,0x70,0x00,0x70,0x00,0x70,0x00,
0x70,0x00,0x70,0x00,0x70,0x00,0x70,0x00,0x70,0x00,0x60,0x00,0x5F,0xF8,0x3F,0xFC,
0x5F,0xFA,0x60,0x06,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,
0x70,0x0E,0x70,0x0E,0x70,0x0E,0x6F,0xF6,0x5F,0xFA,0x3F,0xFC,0x00,0x00,0x00,0x00},
{// 图片数字7
0x00,0x00,0x7F,0xFC,0x3F,0xFA,0x1F,0xF6,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,
0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x06,0x00,0x02,0x00,0x00,
0x00,0x02,0x00,0x06,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,
0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x06,0x00,0x02,0x00,0x00,0x00,0x00},
{// 图片数字8
0x00,0x00,0x3F,0xFC,0x5F,0xFA,0x6F,0xF6,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,
0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x60,0x06,0x5F,0xFA,0x3F,0xFC,
0x5F,0xFA,0x60,0x06,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,
0x70,0x0E,0x70,0x0E,0x70,0x0E,0x6F,0xF6,0x5F,0xFA,0x3F,0xFC,0x00,0x00,0x00,0x00},
{// 图片数字9
0x00,0x00,0x3F,0xFC,0x5F,0xFA,0x6F,0xF6,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,
0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x70,0x0E,0x60,0x06,0x5F,0xFA,0x3F,0xFC,
0x1F,0xFA,0x00,0x06,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,0x00,0x0E,
0x00,0x0E,0x00,0x0E,0x00,0x0E,0x1F,0xF6,0x3F,0xFA,0x7F,0xFC,0x00,0x00,0x00,0x00},
{// 温度符号
0x00,0x00,0x00,0x00,0x70,0xE0,0x53,0xF0,0x77,0xFA,0x0E,0x0E,0x0C,0x06,0x18,0x06,
0x18,0x02,0x38,0x02,0x30,0x00,0x30,0x00,0x70,0x00,0x60,0x00,0x60,0x00,0x60,0x00,
0x60,0x00,0x60,0x00,0x70,0x00,0x30,0x00,0x30,0x00,0x38,0x00,0x18,0x02,0x18,0x02,
0x0C,0x06,0x0E,0x06,0x07,0x0E,0x03,0xFA,0x00,0xF0,0x00,0x60,0x00,0x00,0x00,0x00}};
/*===================== 显示模式3数字图片（宽度x高度=24*32）=========================*/
uchar code mode_3num[10][96]={
{// 图片数字0
0x00,0x7E,0x00,0x01,0xE7,0x80,0x03,0xC3,0xC0,0x07,0x81,0xE0,0x0F,0x80,0xF0,0x0F,
0x00,0xF0,0x1F,0x00,0xF8,0x1E,0x00,0xF8,0x3E,0x00,0x78,0x3E,0x00,0x7C,0x3E,0x00,
0x7C,0x3E,0x00,0x7C,0x3E,0x00,0x7C,0x3E,0x00,0x7C,0x3E,0x00,0x7C,0x3E,0x00,0x7C,
0x3E,0x00,0x7C,0x3E,0x00,0x7C,0x3E,0x00,0x7C,0x3E,0x00,0x7C,0x3E,0x00,0x7C,0x3E,
0x00,0x7C,0x3E,0x00,0x7C,0x3E,0x00,0x78,0x1E,0x00,0xF8,0x1F,0x00,0xF8,0x0F,0x00,
0xF0,0x0F,0x81,0xF0,0x07,0x81,0xE0,0x03,0xC3,0xC0,0x01,0xE7,0x80,0x00,0x7E,0x00},
{// 图片数字1
0x00,0x0C,0x00,0x00,0x1C,0x00,0x00,0x7C,0x00,0x07,0xFC,0x00,0x00,0x3C,0x00,0x00,
0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,
0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,
0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,
0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,
0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3E,0x00,0x00,0x7F,0x00,0x07,0xFF,0xF0},
{// 图片数字2
0x00,0xFF,0x00,0x03,0xC7,0xC0,0x07,0x01,0xE0,0x0E,0x00,0xF0,0x1E,0x00,0xF8,0x1E,
0x00,0xF8,0x3E,0x00,0x78,0x3E,0x00,0x78,0x3F,0x00,0x78,0x3F,0x00,0x78,0x1F,0x00,
0xF8,0x00,0x00,0xF8,0x00,0x00,0xF0,0x00,0x01,0xF0,0x00,0x03,0xE0,0x00,0x03,0xC0,
0x00,0x07,0x80,0x00,0x0F,0x00,0x00,0x1E,0x00,0x00,0x3C,0x00,0x00,0x78,0x00,0x00,
0xF0,0x00,0x01,0xE0,0x00,0x03,0xC0,0x00,0x07,0x80,0x1C,0x07,0x00,0x1C,0x0E,0x00,
0x38,0x1C,0x00,0x38,0x3C,0x00,0x78,0x3F,0xFF,0xF8,0x3F,0xFF,0xF8,0x3F,0xFF,0xF8},
{// 图片数字3
0x00,0xFE,0x00,0x07,0x87,0x80,0x0F,0x03,0xC0,0x1E,0x01,0xE0,0x1E,0x01,0xF0,0x1E,
0x01,0xF0,0x1F,0x00,0xF0,0x1F,0x00,0xF0,0x1E,0x00,0xF0,0x00,0x00,0xF0,0x00,0x01,
0xF0,0x00,0x01,0xF0,0x00,0x03,0xE0,0x00,0x03,0xC0,0x00,0x0F,0x00,0x00,0xFE,0x00,
0x00,0x07,0x80,0x00,0x01,0xE0,0x00,0x00,0xF0,0x00,0x00,0xF8,0x00,0x00,0xF8,0x00,
0x00,0x78,0x00,0x00,0x7C,0x1E,0x00,0x7C,0x3F,0x00,0x7C,0x3F,0x00,0x7C,0x3F,0x00,
0x78,0x3E,0x00,0xF8,0x1E,0x00,0xF0,0x0F,0x01,0xE0,0x07,0x87,0xC0,0x01,0xFF,0x00},
{// 图片数字4
0x00,0x03,0xC0,0x00,0x03,0xC0,0x00,0x07,0xC0,0x00,0x0F,0xC0,0x00,0x0F,0xC0,0x00,
0x1F,0xC0,0x00,0x3F,0xC0,0x00,0x3F,0xC0,0x00,0x77,0xC0,0x00,0x77,0xC0,0x00,0xE7,
0xC0,0x01,0xC7,0xC0,0x01,0xC7,0xC0,0x03,0x87,0xC0,0x07,0x07,0xC0,0x07,0x07,0xC0,
0x0E,0x07,0xC0,0x1E,0x07,0xC0,0x1C,0x07,0xC0,0x38,0x07,0xC0,0x38,0x07,0xC0,0x7F,
0xFF,0xFE,0x7F,0xFF,0xFE,0x00,0x07,0xC0,0x00,0x07,0xC0,0x00,0x07,0xC0,0x00,0x07,
0xC0,0x00,0x07,0xC0,0x00,0x07,0xC0,0x00,0x07,0xC0,0x00,0x07,0xE0,0x00,0x7F,0xFE},
{// 图片数字5
0x0F,0xFF,0xF8,0x0F,0xFF,0xF8,0x0F,0xFF,0xF8,0x0E,0x00,0x00,0x0E,0x00,0x00,0x0E,
0x00,0x00,0x0E,0x00,0x00,0x0E,0x00,0x00,0x0E,0x00,0x00,0x0E,0x00,0x00,0x0E,0x00,
0x00,0x0E,0x7F,0x00,0x0D,0xFF,0xC0,0x0F,0xC3,0xE0,0x1F,0x01,0xF0,0x1E,0x00,0xF8,
0x1E,0x00,0xF8,0x00,0x00,0x78,0x00,0x00,0x7C,0x00,0x00,0x7C,0x00,0x00,0x7C,0x00,
0x00,0x7C,0x1E,0x00,0x7C,0x3F,0x00,0x7C,0x3F,0x00,0x78,0x3F,0x00,0x78,0x3E,0x00,
0xF8,0x1E,0x00,0xF0,0x1E,0x01,0xF0,0x0E,0x01,0xE0,0x07,0x87,0xC0,0x00,0xFF,0x00},
{// 图片数字6
0x00,0x3F,0xC0,0x00,0xF1,0xE0,0x03,0xC1,0xF0,0x07,0x81,0xF8,0x07,0x01,0xF8,0x0F,
0x00,0xF0,0x1F,0x00,0x00,0x1E,0x00,0x00,0x1E,0x00,0x00,0x3E,0x00,0x00,0x3E,0x00,
0x00,0x3E,0x00,0x00,0x3E,0x3F,0x80,0x3E,0xFF,0xE0,0x3F,0xE3,0xF0,0x3F,0x80,0xF8,
0x3F,0x00,0xF8,0x3F,0x00,0x7C,0x3E,0x00,0x7C,0x3E,0x00,0x7C,0x3E,0x00,0x3C,0x3E,
0x00,0x3C,0x3E,0x00,0x3C,0x3E,0x00,0x3C,0x3E,0x00,0x7C,0x1E,0x00,0x7C,0x1F,0x00,
0x78,0x0F,0x00,0x78,0x0F,0x80,0xF0,0x07,0xC0,0xE0,0x03,0xE3,0xC0,0x00,0xFF,0x00},
{// 图片数字7
0x1F,0xFF,0xFC,0x1F,0xFF,0xFC,0x1F,0xFF,0xF8,0x1F,0x00,0x38,0x1C,0x00,0x70,0x1C,
0x00,0xE0,0x38,0x00,0xE0,0x38,0x01,0xC0,0x00,0x01,0xC0,0x00,0x03,0x80,0x00,0x03,
0x80,0x00,0x07,0x80,0x00,0x07,0x00,0x00,0x0F,0x00,0x00,0x0E,0x00,0x00,0x1E,0x00,
0x00,0x1E,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x3C,0x00,0x00,0x7C,0x00,0x00,
0x78,0x00,0x00,0x78,0x00,0x00,0xF8,0x00,0x00,0xF8,0x00,0x00,0xF8,0x00,0x00,0xF8,
0x00,0x00,0xF8,0x00,0x00,0xF8,0x00,0x00,0xF8,0x00,0x00,0xF8,0x00,0x00,0x78,0x00},
{// 图片数字8
0x00,0xFF,0x00,0x07,0xC3,0xC0,0x0F,0x00,0xE0,0x1E,0x00,0xF0,0x1E,0x00,0x78,0x3C,
0x00,0x78,0x3C,0x00,0x78,0x3C,0x00,0x7C,0x3E,0x00,0x78,0x3E,0x00,0x78,0x1F,0x00,
0x78,0x1F,0x80,0xF0,0x0F,0xE1,0xE0,0x07,0xFB,0xC0,0x01,0xFF,0x80,0x01,0xFF,0x80,
0x07,0xBF,0xC0,0x0F,0x0F,0xE0,0x1E,0x03,0xF0,0x3E,0x01,0xF8,0x3C,0x00,0xF8,0x3C,
0x00,0x7C,0x7C,0x00,0x7C,0x78,0x00,0x3C,0x78,0x00,0x3C,0x7C,0x00,0x3C,0x3C,0x00,
0x78,0x3C,0x00,0x78,0x1E,0x00,0x70,0x0F,0x00,0xE0,0x07,0xC3,0xC0,0x01,0xFF,0x00},
{// 图片数字9
0x01,0xFE,0x00,0x07,0xC7,0x80,0x0F,0x01,0xE0,0x1E,0x01,0xE0,0x1E,0x00,0xF0,0x3E,
0x00,0xF8,0x3C,0x00,0x78,0x3C,0x00,0x78,0x7C,0x00,0x7C,0x7C,0x00,0x7C,0x7C,0x00,
0x7C,0x7C,0x00,0x7C,0x7C,0x00,0x7C,0x3C,0x00,0xFC,0x3E,0x00,0xFC,0x3E,0x01,0xFC,
0x1F,0x03,0xFC,0x1F,0x8F,0xFC,0x0F,0xFF,0x7C,0x03,0xFC,0x7C,0x00,0x00,0x7C,0x00,
0x00,0xF8,0x00,0x00,0xF8,0x00,0x00,0xF8,0x00,0x00,0xF0,0x00,0x01,0xF0,0x0F,0x01,
0xE0,0x1F,0x01,0xE0,0x1F,0x03,0xC0,0x1F,0x07,0x80,0x0F,0x9F,0x00,0x03,0xFC,0x00}};
/*========================== 标记及点图片（宽度x高度=16*16）===========================*/
uchar code running[7][32]={
{// 警报标记16*16
0x00,0x00,0x00,0x39,0x00,0x7B,0x00,0xFE,0x01,0xDC,0x0F,0x98,0x0F,0x18,0x0C,0x1F,
0x0C,0x1F,0x0F,0x18,0x0F,0x98,0x01,0xDC,0x00,0xFE,0x00,0x7B,0x00,0x39,0x00,0x00,},
{// 闹铃开启标记16*16
0x00,0x00,0x00,0x40,0x00,0xE0,0x01,0xB0,0x01,0xB0,0x03,0x18,0x03,0x18,0x06,0x0C,
0x0C,0x06,0x0C,0xE6,0x1B,0x1B,0x0C,0x06,0x06,0x0C,0x03,0xF8,0x00,0xE0,0x00,0x00},
{// 键盘锁标记16*16
0x00,0x00,0x01,0xF8,0x03,0xFC,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0xFC,0x06,0x96,
0x0E,0xA7,0x0E,0xC7,0x0E,0xA7,0x0E,0x97,0x07,0xFE,0x03,0xFC,0x01,0xF8,0x00,0x00,},
{// 温度计标记16*16
0x00,0x00,0x1F,0xF8,0x1F,0xF8,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0x80,
0x01,0x90,0x01,0x98,0x01,0x9C,0x01,0x9E,0x01,0x9C,0x00,0x18,0x00,0x10,0x00,0x00},
{// 模式3点16*16
0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xC0,0x03,0xC0,0x03,0xC0,0x03,0xC0,0x03,0xC0,
0x03,0xC0,0x03,0xC0,0x03,0xC0,0x03,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},
{// 模式2点16*16
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xC0,0x03,0xC0,0x03,0xC0,0x03,0xC0,
0x03,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},
{// 篮球器运行标记16*16
0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xF8,0x1F,0xF8,0x01,0x80,0x01,0x80,0x01,0x90,
0x01,0x98,0x01,0x9C,0x01,0x9E,0x01,0x9C,0x01,0x98,0x01,0x90,0x00,0x00,0x00,0x00}};
/*========================== 菜单按钮图片（宽度x高度=16*8）============================*/
uchar code menu_key[]=
{//菜单按钮
0x7F,0xFE,0x81,0x81,0x83,0xC1,0x87,0xE1,0x8F,0xF1,0x9F,0xF9,0x80,0x01,0x7F,0xFE
};
/*=====================================================================================
函数名称：定时器中断处理与初始化，延时
功能描述：时钟更新、篮球器计时
全局变量：time_tick、time_tick1、resu[2]、resu[3]、resu[4]、temp_delay、temp_min
参数说明：无
返回说明：t0_isr(中断标记)、b20time(温度更新标记)
设计人：JZHG
版本：1.0
说明：
======================================================================================*/
/*延时（一次10个机器周期不等）参数格式：延时数*/
void delay(unsigned int det)
{
while(det--);
}
/*1s延时*/
void delay_pw()
{
delay(60000);
delay(60000);
}
/*6个周期 6us */
void delay_b20(uchar n)
{
while(n--);
}
/*主时钟中断处理*/
void time0_isr(void) interrupt 1 using 1
{
TR0=0;
TL0=(time_count&0x00FF);
TH0=(time_count>>8);
TR0=1;
if(--time_tick) return;
time_tick=20;
t0_isr=1;
if(nba_tim&!oth_run) // 当在篮球器界面时 nba_tim==1、oth_run==0
{
if(resu[3]==0)
{
resu[3]=59;
if(resu[2]>0) resu[2]--;
}
else resu[3]--;
if(resu[2]==0&resu[3]==0) // 比赛时间到后停止
{
TR0=0;TR1=0;EA=0;
}
return;
}
if((++temp_min)==60) // 实现温度的更新
{
temp_min=0;
temp_delay--;
if(temp_delay==0)
{
b20time=1;temp_delay=5;
}
}
}
/*24时钟中断处理*/
void time1_isr(void) interrupt 3 using 2
{
TR1=0;
TL1=(time_count&0x00FF);
TH1=(time_count>>8);
TR1=1;
if(--time_tick1) return;
time_tick1=20;
if(resu[4]>0)resu[4]--; // 篮球器24秒中断
t0_isr=1;
if(resu[4]==0)
{ TR0=0;TR1=0;EA=0;}
}
/*定时器初始化*/
void time_init()
{
EA=0;
TR0=0;
TR1=0;
TMOD=0x11;
TL0=(time_count&0x00FF);
TH0=(time_count>>8);
TL1=(time_count&0x00FF);
TH1=(time_count>>8);
IE=0;
ET0=1;
ET1=1;
}
/*=====================================================================================
函数名称：LCD驱动
功能描述：基本驱动（写1个字节、清屏、初始化）
全局变量：无
参数说明：dat_comm（0：命令 1：数据）,content（数值）
返回说明：无返回值
设计人：JZHG
版本：1.0
说明：
======================================================================================*/
/*检查忙碌位*/
void chk_busy (void)
{
lcd_data = 0xff;
lcd_rs = 0; // 命令
lcd_rw = 1; // 读
lcd_e = 1;
while(busy==1);
lcd_e = 0;
}
/*写LCD 参数格式：0:命令,1:数值，数据*/
void wr_lcd (uchar dat_comm,uchar content)
{
chk_busy ();
lcd_rs=dat_comm;
lcd_rw = 0; // 写
lcd_data=content; // 输出数据或命令
lcd_e=1;
lcd_e=0;
}
/*清绘图*/
void clrgdram(void)
{
uchar i,j;
for(j=0;j<32;j++)
{
wr_lcd(comm,0x34);
wr_lcd(comm,0x80+j);
wr_lcd(comm,0x80);
wr_lcd(comm,0x30);
for(i=0;i<32;i++)
wr_lcd(dat,0x00); // 写入0x00
}
wr_lcd(comm,0x36);
}
/*清除显示*/
void clear_dis(void)
{
wr_lcd(comm,0x30);
wr_lcd(comm,0x01); // 清屏，地址指针指向00H
clrgdram(); // 请绘图RAM
}
/*开机LCD初始化*/
void init_lcd (void)
{
lcd_rst=1;
wr_lcd(comm,0x30); // 30---基本指令动作
wr_lcd(comm,0x06); // 光标的移动方向
wr_lcd(comm,0x0c); // 开显示，关游标
clear_dis();
}
/*=====================================================================================
函数名称：DS1302驱动
功能描述：基本驱动（读写数据、读写日期，时间、初始化）
全局变量：无
参数说明：w_adder（写地址）,r_adder（读地址），w_data（写入数据）
返回说明：返回读取的数据
设计人：JZHG
版本：1.0
说明：上升沿写入数值，下降沿读出数值，没用设立后背电池充电
======================================================================================*/
/*向1302写数据参数格式：地址，数据*/
void w1302(uchar w_adder,uchar w_data)
{
uchar d;
ret_ds1302();
for(d=0;d<16;d++)
{
if(d==8) w_adder=w_data;
d02_data=(bit)(w_adder&0x01);
d02_sclk=0; // 上升沿
w_adder>>=1;
d02_sclk=1;
}
end_ds1302();
}
/*接收1302一个字节的数据参数格式：读地址*/
uchar r1302(uchar r_adder)
{
uchar d=0;
ret_ds1302();
for(d=0;d<8;d++) // 写地址
{
d02_data=(bit)(r_adder&0x01);
d02_sclk=0;
r_adder>>=1;
d02_sclk=1;
}
r_adder=0;
for(d=0;d<8;d++) // 读数据
{
d02_data=1;
d02_sclk=1; // 下降沿
r_adder>>=1;
d02_sclk=0;
if(d02_data) r_adder|=0x80;
}
end_ds1302();
return(r_adder);
}
/*写入时间与日期*/
void wds1302_time_date(void)
{
w1302(d02_wrc,0x00); // 写允许
w1302(0x90,0xa5); // 单二极管2K电阻充电
w1302(d02_year,today.year); // 年
w1302(d02_weeks,today.week); // 星期
w1302(d02_month,today.month); // 月
w1302(d02_day,today.day); // 日
w1302(d02_hour,0x7f&now.hour); // 时
w1302(d02_minute,now.minute); // 分
w1302(d02_second,0x7f&now.second); // 秒
w1302(d02_wrc,0x80); // 写禁止
}
/*初始化写DS1302 RAM*/
void init_wds1302_ram(void)
{
w1302(d02_wrc,0x00);
w1302(0x90,0xa5); // 单二极管2K电阻充电
w1302(d02_signs,0x00); // 状态寄存
w1302(d02_passw,0x62); // 密码储存首位
w1302(d02_passw+2,0x18); // 初始值为:741456
w1302(d02_passw+4,0x29); // 密码最后一位
w1302(d02_alm,0x12); // 闹铃时(12小时)
w1302(d02_alm+2,0x00); // 闹铃分(0分)
w1302(d02_temp,0xff); // 温度上限(255为关闭)
w1302(d02_temp+2,0xff); // 温度下限(关闭)
w1302(d02_initsi,0xb4); // 是否要初始化标记(0xb4为已经初始化)
w1302(d02_wrc,0x80);
}
/*写DS1302一字节的RAM*/
void wds1302_data(uchar adder,uchar _data)
{
w1302(d02_wrc,0x00);
w1302(adder,_data);
w1302(d02_wrc,0x80);
}
/*读取日期*/
void rds1302_date(void)
{
today.year=r1302(d02_year+1);
today.week=r1302(d02_weeks+1);
today.month=r1302(d02_month+1);
today.day=r1302(d02_day+1);
}
/*读取时间*/
void rds1302_time(void)
{
now.hour=(r1302(d02_hour+1));
now.minute=r1302(d02_minute+1);
now.second=r1302(d02_second+1);
if(now.hour==alarm_time[0]&&now.minute==alarm_time[1]) alm_run=1;
else // 闹铃时间比较
{
alm_run=0;buzstop=0;buzzer=close;
}
}
/*开机读数据*/
void rds1302_data(void)
{
signs=r1302(d02_signs+1);
alarm_time[0]=r1302(d02_alm+1);
alarm_time[1]=r1302(d02_alm+3);
als_temp[0]=r1302(d02_temp+1);
als_temp[1]=r1302(d02_temp+3);
}
/*DS1302初始化*/
void init_ds1302(void)
{
wds1302_time_date();
init_wds1302_ram();
}
/*=====================================================================================
函数名称：DS18b20驱动
功能描述：基本驱动（读写数据、数据转换、初始化）
全局变量：无
参数说明：无
返回说明：返回读取的数据
设计人：JZHG
版本：1.0
说明：调试中。。。
======================================================================================*/
/*18B20初始化*/
void init_ds18b20()
{
b20_io=1;
delay_b20(8);
b20_io=0;
delay_b20(120); // 延时≥480us
b20_io=1;
delay_b20(12); // 拉高为高电平后在15—60us出现低电平，并维持60—240us
ds18b20=~b20_io;
delay_b20(40);
}
/*向18B20发送一个字节*/
void send18b20_byte(uchar data_send)
{
uchar d=0;
for (d=0;d<8;d++)
{
b20_io=0; // 拉低电平后向总线写入一个位，15us后18B20接收
b20_io=data_send&0x01;
delay_b20(10); // 延时60us后完成一次
b20_io=1;
data_send>>=1; // 下位开始
}
}
/*从18B20读出温度值 12位分辨率*/
void receive18b20(void)
{
uchar n=1,d;
for (d=0;d<16;d++)
{
if(d==8) n=0;
b20_io=0; // 拉低总线
temp.t_data[n]>>=1;
b20_io=1; // 拉高总线
if(b20_io) // 读入总线数值
temp.t_data[n]|=0x80;
delay_b20(10); // 等待60us
}
}
/*数据转化*/
void conversion_t(void)
{
uchar save=0,save1=0;
if(temp.temp_data<0) // 判断数值符号
{temp_pn=1;temp.temp_data=~temp.temp_data+1;}
else temp_pn=0;
if(temp.t_data[1]&0x01==1) save+=6; // 小数点后的值转变
if((temp.t_data[1]>>1)&0x01==1) save+=12;
if((temp.t_data[1]>>2)&0x01==1) save+=25;
if((temp.t_data[1]>>3)&0x01==1) save+=50;
temp.temp_data>>=4;
save1=temp.temp_data&0x00ff; // 整数部分数值
temp.t_data[0]=save1;
temp.t_data[1]=save;
thl_als=1;
if(save1>=(als_temp[0]&0x7f)) // 温度比较
{
if(!temp_pn||(temp_pn&(als_temp[0]&0x80)!=0)){ als_th=open;als_tl=close;}
}
else if(save1<(als_temp[1]&0x7f)&&als_temp[1]!=255)
{
if(!temp_pn||(temp_pn&(als_temp[1]&0x80)!=0)) {als_tl=open;als_th=close;}
}
else {als_th=als_tl=close;thl_als=0;buzstop=0;buzzer=close;}
}
/*18b20功能*/
void ds18b20_func(void)
{
EA=0;
TR0=0;
temp.temp_data=0;
init_ds18b20();
send18b20_byte(0xcc); // 跳过ROM
send18b20_byte(0x44); // 温度转换
delay_pw();
init_ds18b20();
send18b20_byte(0xcc);
send18b20_byte(0xbe); // 读RAM
receive18b20(); // 读取温度值
conversion_t(); // 数值转换
EA=1;
TR0=1;
}
/*=====================================================================================
函数名称：画面构造
功能描述：界面1、2、3，图片菜单，反白，标头，16*16（32）图片
全局变量：无
参数说明：函数说明
返回说明：无
设计人：JZHG
版本：1.0
说明：X坐标每一格每次16点
======================================================================================*/
/*反白或显示图片参数格式：(H)8bit数据，(L)8bit数据,X0坐标(16bit)，Y0坐标(1bit),X坐标(16bit)，Y坐标(1bit)*/
void con_disp (uchar data1,uchar data2,uchar x0,uchar y0,uchar xl,uchar yl)
{
uchar i,j;
for(j=0;j<yl;j++)
{
for(i=0;i<xl;i++)
{
wr_lcd(comm,0x34); // 扩展功能
wr_lcd(comm,y0+j); // 写Y坐标
wr_lcd(comm,x0+i); // 写X坐标
wr_lcd(comm,0x30); // 普通功能
wr_lcd(dat,data1);
wr_lcd(dat,data2);
}
}
wr_lcd(comm,0x36); // 开绘图显示
}
/*显示字体参数格式: 显示位置(0x80-0x9f),显示个数，显示内容指针*/
void display_cnasc(uchar dis_bit,uchar num,uchar *cnasc)
{
wr_lcd(comm,0x30); // 普通功能
wr_lcd(comm,dis_bit); // 写地址
while(num>0)
{
wr_lcd(dat,*(cnasc++));
wr_lcd(dat,*(cnasc++));
num--;
}
}
/*导航标头显示*/
void dis_title(void)
{
display_cnasc(0x80,1,"\x15 ");
display_cnasc(0x90,1,"┏");
display_cnasc(0x97,1,"┓");
display_cnasc(0x98,1,"┗");
display_cnasc(0x9f,1,"┛");
display_cnasc(0x92,1,"\x1e ");
display_cnasc(0x9a,1,"\x1f ");
con_disp(0xff,0xff,0x80,0x80,3,16);
con_disp(0xef,0xef,0x83,0x80,1,16);
con_disp(0xde,0xf7,0x84,0x80,1,16);
con_disp(0x76,0xdb,0x85,0x80,1,16);
con_disp(0x55,0x55,0x86,0x80,1,16);
con_disp(0x55,0x55,0x87,0x80,1,16);
}
/*图片显示标头*/
void dis_title_pic(void)
{
display_cnasc(0x80,2,"〓〓");
display_cnasc(0x86,2,"〓〓");
}
/*功能实现显示标头*/
void dis_title_e(void)
{
display_cnasc(0x80,1," \x15");
con_disp(0xff,0xff,0x80,0x80,1,16);
con_disp(0xff,0xc7,0x81,0x80,1,16);
con_disp(0xff,0xff,0x82,0x80,3,16);
con_disp(0xe3,0xff,0x85,0x80,1,16);
con_disp(0xff,0xff,0x86,0x80,2,16);
}
/*显示菜单图片格式：图片反显(1)或正常显示(0)，显示图片的号码*/
void anti_nor_pic (uchar cpl_sign,uchar menu_num)
{
uchar i,j,x,y;
x=menu_num*3; // 计算图片显示坐标
if(x>6) x--;
if(menu_num<3) y=16; // 上下半屏显示
else y=8;
if(cpl_sign==1) display_cnasc(0x82,4,menu_cn[menu_num]);
for(j=0;j<24;j++)
{
for(i=0;i<2;i++)
{
wr_lcd(comm,0x34);
wr_lcd(comm,0x80+y);
wr_lcd(comm,0x80+x+i); // 分两次显示 16bit
wr_lcd(comm,0x30);
if(cpl_sign==1) // 图片反选
{
wr_lcd(dat,~menu_pic[menu_num][j*4+i*2]);
wr_lcd(dat,~menu_pic[menu_num][j*4+i*2+1]);
}
else // 正常显示
{
wr_lcd(dat,menu_pic[menu_num][j*4+i*2]);
wr_lcd(dat,menu_pic[menu_num][j*4+i*2+1]);
}
}
y++;
if(y==32&&menu_num<3) {x+=8;y=0;} // 上下屏切换
}
wr_lcd(comm,0x36);
}
/*状态16*16图片格式：反色（1）或正常0，X坐标，Y坐标，状态编码（16*16）*/
void dis_run_state(uchar cpl,uchar x0,uchar y0,uchar state_num)
{
uchar j;
for(j=0;j<16;j++)
{
wr_lcd(comm,0x34); // 扩展功能
wr_lcd(comm,y0++); // 写Y地址
wr_lcd(comm,x0); // 写X地址
wr_lcd(comm,0x30); // 普通功能
if(cpl==1) // 写数据
{
wr_lcd(dat,~running[state_num][j*2]);
wr_lcd(dat,~running[state_num][j*2+1]);
}
else
{
wr_lcd(dat,running[state_num][j*2]);
wr_lcd(dat,running[state_num][j*2+1]);
}
}
wr_lcd(comm,0x36);
}
/*显示菜单按钮参数格式：反色(1)或正常(0)*/
void dis_menu_key(uchar d)
{
if(d==1)
{
for(d=0;d<8;d++) // 显示菜单按钮
con_disp(~menu_key[d*2],~menu_key[d*2+1],0x9f,0x97+d,1,1);
}
else
{
for(d=0;d<8;d++) // 显示菜单按钮
con_disp(menu_key[d*2],menu_key[d*2+1],0x9f,0x97+d,1,1);
}
}
/*显示模式3的界面*/
void dis_mode3(void)
{
uchar i,j,h,l,x_0=0x80,y_0=0x90;
h=now.hour>>4; // 分离十位个位
l=now.hour&0x0f;
for(j=0;j<2;j++)
{
for(i=0;i<32;i++) // 十位个位一起读入
{
wr_lcd(comm,0x34);
wr_lcd(comm,y_0++);
wr_lcd(comm,x_0);
wr_lcd(comm,0x30);
wr_lcd(dat,mode_3num[h][i*3]); // 连续写数据，X坐标自动加1
wr_lcd(dat,mode_3num[h][i*3+1]);
wr_lcd(dat,mode_3num[h][i*3+2]);
wr_lcd(dat,mode_3num[l][i*3]);
wr_lcd(dat,mode_3num[l][i*3+1]);
wr_lcd(dat,mode_3num[l][i*3+2]);
if(y_0==0xa0){x_0=x_0+8;y_0=0x80;}
}
x_0=0x84,y_0=0x90;
h=now.minute>>4; // 分离十位个位
l=now.minute&0x0f;
}
dis_run_state(0,0x83,0x90,4); // 显示点
dis_run_state(0,0x8b,0x80,4);
y_0=0x80; // 显示状态标记
if(keb) {dis_run_state(0,0x87,y_0,2);y_0+=16;}
if(alm) {dis_run_state(0,0x87,y_0,1);y_0+=16;}
if(y_0<0xa0&&!als){dis_run_state(0,0x87,y_0,0);}
if(y_0==0xa0&&!als){dis_run_state(0,0x8f,0x80,0);}
dis_menu_key(0);
}
/*显示模式1和2的共用部分*/
void mode1_2_union(void)
{
uchar x=0x9b;
display_cnasc(0x98,2,"星期");
if(nba_tim) dis_run_state(0,x,0x90,6);
if(keb) {dis_run_state(0,x,0x90,2);x++;} // 显示标记
if(alm) {dis_run_state(0,x,0x90,1);x++;}
if(!als){dis_run_state(0,x,0x90,0);}
dis_menu_key(0); // 显示菜单按钮
}
/*显示模式2的日期*/
void dis_date_mode2(uchar d)
{
uchar save[2];
display_cnasc(d+2,1,"年");
display_cnasc(d+4,1,"月");
display_cnasc(d+6,1,"日");
display_cnasc(0x9a,1,weeks[today.week]); // 显示星期
save[0]=char_num[today.year>>4]; // 将显示的数值存到数组中
save[1]=char_num[today.year&0x0f];
display_cnasc(d+1,1,save);
save[0]=char_num[today.month>>4];
save[1]=char_num[today.month&0x0f];
display_cnasc(d+3,1,save);
save[0]=char_num[today.day>>4];
save[1]=char_num[today.day&0x0f];
display_cnasc(d+5,1,save);
}
/*显示模式2的时间数字显示 16*32*/
void num2_asc_dis(uchar num,uchar x_0)
{
uchar i,y_0=0x90;
for(i=0;i<32;i++) // 十位个位一起读入
{
wr_lcd(comm,0x36);
wr_lcd(comm,y_0++);
wr_lcd(comm,x_0);
wr_lcd(comm,0x30);
wr_lcd(dat,mode_2num[num][i*2]);
wr_lcd(dat,mode_2num[num][i*2+1]);
if(i==15){x_0+=8;y_0=0x80;}
}
wr_lcd(comm,0x36);
}
/*显示模式2的时间*/
void dis_time_mode2(void)
{
uchar h,l;
if(now.hour!=save_time.hour||init_d2)
{
h=now.hour>>4; // 分离十位个位
l=now.hour&0x0f;
num2_asc_dis(h,0x80);
num2_asc_dis(l,0x80+1);
}
if(now.minute!=save_time.minute||init_d2)
{
h=now.minute>>4; // 分离十位个位
l=now.minute&0x0f;
num2_asc_dis(h,0x83);
num2_asc_dis(l,0x83+1);
}
if(now.second!=save_time.second||init_d2)
{
h=now.second>>4; // 分离十位个位
l=now.second&0x0f;
num2_asc_dis(h,0x86);
num2_asc_dis(l,0x86+1);
}
if(init_d2)
{
dis_run_state(0,0x82,0x90,5); // 显示点
dis_run_state(0,0x8a,0x80,5);
dis_run_state(0,0x85,0x90,5); // 显示点
dis_run_state(0,0x8d,0x80,5);
}
}
/*显示模式2的界面*/
void dis_mode2(void)
{
dis_date_mode2(0x81); // 显示日期
display_cnasc(0x81,1,"20");
dis_time_mode2(); // 显示时间
mode1_2_union();
}
/*显示模式1的日期*/
void dis_date_mode1(void)
{
uchar save[2];
display_cnasc(0x80,3,"日期：");
display_cnasc(0x90,3,"时间：");
display_cnasc(0x88,3,"温度：");
display_cnasc(0x9a,1,weeks[today.week]); // 显示星期
display_cnasc(0x83,1,"20");
save[0]=char_num[today.year>>4];
save[1]=char_num[today.year&0x0f];
display_cnasc(0x84,1,save);
save[0]='/';
save[1]=char_num[today.month>>4];
display_cnasc(0x85,1,save);
save[0]=char_num[today.month&0x0f];
save[1]='/';
display_cnasc(0x86,1,save);
save[0]=char_num[today.day>>4];
save[1]=char_num[today.day&0x0f];
display_cnasc(0x87,1,save);
mode1_2_union();
}
/*显示模式1的时间*/
void dis_time_mode1(void)
{
uchar save[2];
save[0]=char_num[now.hour>>4];
save[1]=char_num[now.hour&0x0f];
display_cnasc(0x93,1,save);
save[0]=':';
save[1]=char_num[now.minute>>4];
display_cnasc(0x94,1,save);
save[0]=char_num[now.minute&0x0f];
save[1]=':';
display_cnasc(0x95,1,save);
save[0]=char_num[now.second>>4];
save[1]=char_num[now.second&0x0f];
display_cnasc(0x96,1,save);
}
/*显示模式1的温度*/
void dis_temp_mode1(void)
{
uchar save[2];
if(ds18b20)
{
if(temp.t_data[0]>99)
{
save[0]=char_num[temp.t_data[0]/100];
save[1]=char_num[(temp.t_data[0]/10)%10];
display_cnasc(0x8b,1,save);
save[0]=char_num[temp.t_data[0]%10];
save[1]='.';
display_cnasc(0x8c,1,save);
save[0]=char_num[temp.t_data[1]/10];
save[1]=' ';
display_cnasc(0x8d,1,save);
display_cnasc(0x8e,1,"℃");
}
else
{
if(temp_pn) display_cnasc(0x8a,1,":-");
else display_cnasc(0x8a,1,"：");
save[0]=char_num[temp.t_data[0]/10];
save[1]=char_num[temp.t_data[0]%10];
display_cnasc(0x8b,1,save);
save[0]='.';
save[1]=char_num[temp.t_data[1]/10];
display_cnasc(0x8c,1,save);
display_cnasc(0x8d,1,"℃");
}
}
else display_cnasc(0x8b,3,"FF.F℃");
}
/*显示模式1的界面*/
void dis_mode1(void)
{
dis_date_mode1();
dis_time_mode1();
dis_temp_mode1();
}
/*篮球器时间显示*/
void nba_dis_time(void)
{
uchar d,dis[2];
for(d=2;d<4;d++)
{
dis[0]=char_num[resu[d]/10];
dis[1]=char_num[resu[d]%10];
display_cnasc(0x81+d*2,1,dis);
}
display_cnasc(0x86,1,": ");
if(resu[0]==1)
{
dis[0]='\x07';
dis[1]=char_num[resu[4]/10];
display_cnasc(0x93,1,dis);
dis[1]='\x07';
dis[0]=char_num[resu[4]%10];
display_cnasc(0x94,1,dis);
}
}
/*=====================================================================================
函数名称：键盘扫描
功能描述：读取键盘操作数据及部分状态的实现
全局变量：dis_sig t0_isr temprun b20time alm_run als_temp buzstop als
lock_op nba_tim
参数说明：无
返回说明：键盘锁与密码锁时间到达后返回 255
设计人：JZHG
版本：1.0
说明：
======================================================================================*/
/*扫描键盘*/
uchar keypad_scan()
{
uchar key,dis[2];
keyboard=0xf0;
while (keyboard==0xf0) // 等待按键按下
{
/*--------------------- 背光灯关闭延时 -----------------------*/
delay(1000);
if((++dis[0])==0&&bl_delay!=0) bl_delay--; // 当有按键按下bl_delay重新赋值
if(bl_delay==0&&!bl0) lcd_bl=close; // 背光时间到且不是常开模式时关闭背光
/*----------------------- 键盘锁延时 -------------------------*/
if(keb&&dis_sig&&bl_delay==0&&resu[11]<2) resu[11]++; // 当有按键按下j清零
if(bl_delay==0) bl_delay=15;
/*--------------------- 密码锁30秒锁延时 ---------------------*/
if(lock_op)
{
if((++i)==0) save1++;
if(save1==15) return(255);
}
/*---------------------- 时钟界面时间显示 ---------------------*/
if(dis_sig&&t0_isr||nba_tim&&oth_run) // 正常时钟界面与篮球器返回时钟界面显示
{
rds1302_date(); // 读出日期
rds1302_time(); // 读出时间
if(di0) // 模式2
{
dis_time_mode2();
if(now.hour==0&&now.minute==0&&now.second==0) dis_date_mode2(0x81);
}
else if(di1) // 模式3
{
if(now.hour!=save_time.hour||now.minute!=save_time.minute) // 时,分变化后显示
dis_mode3();
}
else
{
dis_time_mode1(); // 模式1
if(now.hour==0&&now.minute==0&&now.second==0) dis_date_mode1();
}
save_time=now; // 重新记录作下次比较
t0_isr=0;
}
/*-------------------- 温度计提示按键操作 ----------------------*/
if(temprun)
{
if(!oth_run)
{
display_cnasc(0x96,2," key"); // 温度计时提示按键操作
for(dis[1]=0;dis[1]<250;dis[1]++)
{
delay(1000);
if(keyboard!=0xf0)
{
keyboard=0x7f;
if(keyboard==0x7d) return 0x7d;
else keyboard=0xf0;
}
}
oth_run=1;
display_cnasc(0x96,2," ");
}
}
/*------------------------ 蜂鸣器警报 --------------------------*/
if(((alm_run&&alm)||thl_als)&&!buzstop) // 温度，闹铃蜂鸣器警报
{ // 有按键按下时停止
if(now.second==0) lcd_bl=close;
delay(15000); // 读出温度时间比较
if(keyboard!=0xf0) break;
delay(15000);
if(keyboard!=0xf0) break;
delay(15000);
if(keyboard!=0xf0) break;
delay(15000);
if(alm_run) lcd_bl=!lcd_bl; // 只在闹铃功能闪
if(!als)buzzer=!buzzer; // 警报开启后蜂鸣器开启
}
/*----------------------- 温度刷新显示 -------------------------*/
if((temprun&&oth_run)||(b20time&&!di0&&!di1&&dis_sig)) // 温度计功能于模式1界面
{
ds18b20_func(); // 温度检测功能
oth_run=0; // 作交替标记用
if(temprun) return 20; // 温度计开启后返回
if(b20time){ dis_temp_mode1();b20time=0;} // 时钟界面5分钟更新一次，T0计时
}
/*------------------------ 篮球器显示时间 ------------------------*/
if(nba_tim&!oth_run) // 当篮球器模式下 oth_run==0为篮球器计时状态
{
if(EA) display_cnasc(0x8b,2," R\x10 "); // 显示运行状态
else display_cnasc(0x8b,2," S! ");
if(t0_isr)
{ // 更新时间
nba_dis_time();
if(resu[2]==0&&resu[3]==0) // 判断比赛情况
{
resu[6]++;
if(resu[6]<resu[1]) display_cnasc(0x85,3,"休息 ");
else display_cnasc(0x85,3,"完结 ");
}
if(resu[4]==0||(resu[2]==0&&resu[3]==0)) // 时间到达警报
{
buzzer=open;
delay_pw();
if(resu[2]==0&&resu[3]==0) // 24秒总时间警报
{
delay_pw();
}
buzzer=close;
if(resu[4]==0) resu[4]=24; // 重新赋值
}
t0_isr=0; // 清零等下次中断产生
}
}
}
/*===== 以上等待按键 =====*/
/*------------------------- 按键按下后 --------------------------*/
delay(8000); // 消抖振
if(!lock_op)bl_delay=15; // 背光时间赋值
if(bl1) lcd_bl=close; // 不在背光灯关闭时亮起
else lcd_bl=open;
if(alm_run|thl_als) {buzstop=1;buzzer=close;}
if(keb&&dis_sig)
{
if(resu[11]==2) return 255; // 要求输入密码
else resu[11]=0; // 时间不到时重新计时
}
do
{
for(dis[0]=0;dis[0]<=3;dis[0]++)
{
keyboard=ksp[dis[0]];
if(keyboard!=ksp[dis[0]])
{
key=keyboard;
if(key!=ksp[dis[0]]) return(key);
}
}
}while(1);
}
/*读键盘数据*/
uchar gotkey()
{
uchar save,n;
keyboard=0xf0;
while(keyboard!=0xf0); // 等待键盘松开
delay(5000); // 消抖阵
if(adju_si) // 连写输入
{
adju_si=0;
for(n=0;n<60;n++)
{
delay(2000);
if(keyboard!=0xf0)
{
adju_si=1; // 在更改时,在此时间内可连成多位数
break;
}
}
}
save=keypad_scan(); // 扫描键盘
if(save==255) return 255; // 要求输入键盘锁密码或延时时间到达
for (n=0;n<16;n++)
{
if(save==key_code[n])
return(n);
}
return(20);
}
/*=====================================================================================
函数名称：导航
功能描述：主菜单工具导航保存提示
全局变量：无
参数说明：
返回说明：无
设计人：JZHG
版本：1.0
说明：
======================================================================================*/
/*按键按下显示参数格式：k 按钮的显示地址*/
void key_dis(uchar k)
{
display_cnasc(k,1,"\x04 ");
delay(10000);
if(k==0x92||k==0x96) display_cnasc(k,1,"\x1e ");
else display_cnasc(k,1,"\x1f ");
}
/*确定按键按下显示*/
void enter_dis(void)
{
display_cnasc(0x8f,1," \x09");
delay(15000);
}
/*主菜单导航*/
uchar dis_menu(void)
{
uchar d,save,key;
if(meu)
{
display_cnasc(0x81,2,"菜单");
dis_title();
display_cnasc(0x88,8,selected[0]);
con_disp(0xff,0xff,0x8a,0x80,5,16);
}
else // 显示图片菜单
{
dis_title_pic();
for(d=0;d<6;d++)
anti_nor_pic(0,d);
anti_nor_pic(1,0);
}
save=d=0;
do
{
if(meu) // 操作指示更新
{
display_cnasc(0x93,3,menu_cn_2[index_m[save].right_num]);
display_cnasc(0x8b,3,menu_cn_2[save]);
display_cnasc(0x9b,3,menu_cn_2[index_m[save].left_num]);
}
else
{
anti_nor_pic(0,d);
anti_nor_pic(1,save);
}
d=save; // 保存上一索引
while(1)
{
key=gotkey();
if(key==11||(key==3&&meu))
{
if(meu) enter_dis();
break;
}
else if(meu)
{
if(key==2)
{
save=index_m[d].left_num;
key_dis(0x9a);
break;
}
if(key==5)
{
save=index_m[d].right_num;
key_dis(0x92);
break;
}
if((key==1&&meu))
{
d=5;
break;
}
}
else
{
if(key==3){save=index_m[d].left_num; break;} // 根据导航键寻找索引
if(key==1){save=index_m[d].right_num; break;}
if(key==2||key==5){save=index_m[d].shaft_num; break;}
}
}
if(key==11||((key==1|key==3)&&meu)) break;
}while(1);
return d;
}
/*工具导航*/
uchar tool_func(void)
{
uchar save,d,key;
display_cnasc(0x81,2,"工具");
dis_title();
display_cnasc(0x88,8,selected[0]);
con_disp(0xff,0xff,0x8a,0x80,5,16);
d=0;
save=0;
do
{
display_cnasc(0x93,3,tool_menu[index_t[save].lnum]);
display_cnasc(0x8b,3,tool_menu[save]);
display_cnasc(0x9b,3,tool_menu[index_t[save].rnum]);
d=save;
while(1)
{
key=gotkey();
if(key==1){ d=4;break;} // 根据按键寻找索引
if(key==11||key==3){enter_dis();break;}
if(key==2){save=index_t[d].rnum; key_dis(0x9a);break;}
if(key==5){save=index_t[d].lnum; key_dis(0x92);break;}
}
if(key==11||key==3||key==1) break;
}while(1);
return d;
}
/*更改后提示保存*/
void save_y_or_n(void)
{
uchar key;
clear_dis();
oth_run=0;
display_cnasc(0x92,5,"是否保存? ");
display_cnasc(0x89,6,"Y(OK)\\N(./S)");
while(1)
{
key=gotkey();
if(key==11)
{
display_cnasc(0x9a,5,"保存成功！ ");
delay(50000);
oth_run=1; // 要求保存时oth_run标记为1
return;
}
if(key==10) return;
}
}
/*=====================================================================================
函数名称：调整功能
功能描述：时间日期调整
全局变量：today now
参数说明：见函数
返回说明：无
设计人：JZHG
版本：1.0
说明：
======================================================================================*/
/*调整功能显示时间*/
void asjust_time()
{
uchar save[2];
display_cnasc(0x8a,1,"时");
display_cnasc(0x8c,1,"分");
display_cnasc(0x8e,1,"秒");
save[0]=char_num[now.hour>>4];
save[1]=char_num[now.hour&0x0f];
display_cnasc(0x89,1,save);
save[0]=char_num[now.minute>>4];
save[1]=char_num[now.minute&0x0f];
display_cnasc(0x8b,1,save);
save[0]=char_num[now.second>>4];
save[1]=char_num[now.second&0x0f];
display_cnasc(0x8d,1,save);
}
/*调整功能月天数比较*/
uchar monthday(uchar year,uchar month)
{
if(month==2&&year%4==0)
return(29);
else
{ year=month&0x0f;
month>>=4;
month=month*10+year;
return(dayofmonth[month-1]);}
}
/*星期推算*/
void weeks_day()
{
uchar d,buffer,day=4;
if(today.month>1)
{
buffer=(today.month>>4); // 将BCD码转为十进制
buffer=buffer*10;
buffer+=(today.month&0x0f);
for(d=0;d<buffer-1;d++)
{
today.week=(dayofmonth[d]>>4);
today.week=today.week*10;
today.week+=(dayofmonth[d]&0x0f);
day+=(today.week%7);
}
}
buffer=(today.year>>4);
buffer*=10;
buffer+=(today.year&0x0f);
if(today.year!=0)
{
day+=((buffer-1)/4)+buffer+1;
}
if(buffer%4==0&&today.month>2) day++;
buffer=today.day>>4;
buffer*=10;
buffer+=(today.day&0x0f);
today.week=(day+buffer)%7;
}
/*调整功能*/
void adjust_func(void)
{
uchar d,save,b=0;
dis_title_e();
display_cnasc(0x82,3,menu_cn_2[0]);
rds1302_date();
rds1302_time();
dis_date_mode2(0x90);
display_cnasc(0x9a,1," ");
asjust_time();
display_cnasc(0x9f,1,"→");
display_cnasc(0x90,1,"『");
display_cnasc(0x8f,1,"』");
d=0;save=0;
adju_si=0;
do
{
con_disp(0x00,0x00,index_a[d].lnum,index_a[d].rnum,1,13);
con_disp(0xff,0xff,index_a[save].lnum,index_a[save].rnum,1,13);
d=save;
while(1)
{
save=gotkey();
if(save>=0&&save<10)
{
switch(d)
{
case 0: if(adju_si) // adju_si==1时两次输入连成一个数
{
today.year<<=4;
today.year+=save;adju_si=0;
}
else
{
today.year=save;adju_si=1;
}
break;
case 1: if(adju_si)
{
today.month<<=4;today.month+=save;
if(today.month>0x12) today.month=save;
else adju_si=0;
}
else
{
today.month=save;adju_si=1;
}
break;
case 2: if(adju_si)
{
today.day<<=4;today.day+=save; // 月天数比较
if(today.year%4==0&&today.month==2&&today.day==29) ;
else if(today.day>monthday(today.year,today.month))
today.day=save;
else adju_si=0;
}
else {today.day=save;adju_si=1;}
break;
case 3: if(adju_si)
{
now.hour<<=4;now.hour+=save;
if(now.hour>0x23) now.hour=save;
else adju_si=0;
}
else {now.hour=save;adju_si=1;}
break;
case 4: if(adju_si)
{
now.minute<<=4;now.minute+=save;
if(now.minute>0x59) now.minute=save;
else adju_si=0;
}
else {now.minute=save;adju_si=1;}
break;
case 5: if(adju_si)
{
now.second<<=4;now.second+=save;
if(now.second>0x59) now.second=save;
else adju_si=0;
}
else {now.second=save;adju_si=1;}
break;
}
if(today.day>monthday(today.year,today.month)) today.day=1; // 更改月份时判断天数
if(today.month==0) today.month=1;
if(today.day==0) today.day=1;
if(d<3) dis_date_mode2(0x90); // 更新显示
else asjust_time();
display_cnasc(0x9a,1," "); // 消去星期显示
}
if(save==11){save=d+1;adju_si=0;break;}
if(save==10&&d!=0){save=d-1;adju_si=0;break;}
}
if(save==7&d==6) break;
}while(1);
weeks_day(); // 计算星期
save_y_or_n(); // 需要保存时oth_run设为1
if(oth_run) wds1302_time_date();
}
/*=====================================================================================
函数名称：计算器功能
功能描述：10位带符号数的加减乘除运算
全局变量：opera resu i j
参数说明：见函数
返回说明：无
设计人：JZHG
版本：1.0
说明：
======================================================================================*/
/*清寄存器参数格式：m=2时结果寄存器，当m=1时操作数1，当m=0时操作数0(1),
n=1时,只清寄存器不清显示, 0两清*/
void removal_data(uchar m,uchar n)
{
uchar l; // 当n=1时,只清寄存器不清显示, 0两清
if(m==2) // 当m=2时结果寄存器
{ // 当m=1时操作数1
if(n==0) // 当m=0时操作数0 ,1
for(l=0;l<6;l++)
display_cnasc(0x98+l,1," ");
for(l=0;l<12;l++)
resu[l]=0;
}
while(m<2)
{
if(n==0)
{
if(m==0)
{
for(l=0;l<6;l++)
display_cnasc(0x90+l,1," ");
display_cnasc(0x95,1," 0");
}
else
for(l=0;l<6;l++)
display_cnasc(0x88+l,1," ");
}
for(l=0;l<12;l++)
opera[m][l]=0;
m++;
}
}
/*显示数值参数格式：显示首地址*/
void dis_cdata(uchar ass)
{
uchar p,d,save[2];
if(i==0&&opera[0][0]==1) // 显示符号
{
if(cal_run) display_cnasc(0x98,1,"=-");
else display_cnasc(0x90,1," -");
}
d=opera[i][11]; // 计算位数
if(opera[i][10]!=0&&opera[i][10]!=opera[i][11]+1) d++;
save[0]=d/2;ass=ass-save[0]+5; // 计算显示的开始位置
p=1;
cal_del=0; // 显示点标记（0为没有显示）
if(d%2==1) // 对位数位奇数先处理首位
{
save[0]=' ';
save[1]=char_num[opera[i][1]];
display_cnasc(ass,1,save);
p++;
}
ass++; // 显示地址加一
while(p<=opera[i][11])
{
if(opera[i][10]==p&&(!cal_del)) { // 显示点且作标记
save[0]='.';cal_del=1;}
else {
save[0]=char_num[opera[i][p]]; p++;}
if(opera[i][10]==p&&(!cal_del)) {
save[1]='.';cal_del=1;}
else{
save[1]=char_num[opera[i][p]];p++;}
display_cnasc(ass,1,save);
ass++;
}
}
/*从键盘中写入数据*/
char input_data()
{
uchar save=20,c;
for(;i<2;i++)
{
while(1)
{
pp: save=gotkey(); // 读键盘
if(save==20) continue;
if(save==11) // 按键为确定时,选择计算或删除
{
c=save=0;
while(1) // 反色选择
{
con_disp (0x00,0x00,index_cal[save].lnum,index_cal[save].rnum,2,16);
con_disp (0xff,0xff,index_cal[c].lnum,index_cal[c].rnum,2,16);
save=gotkey();
if(save==10)
{
save=c;
if(++c==3) c=0;
}
else if(save==11)
{
if(c==0) save=11;
else if(c==1) save=16;
else return 0;
break;
}
else break;
}
con_disp (0x00,0x00,index_cal[c].lnum,index_cal[c].rnum,2,16);
}
if(save>=0&&save<=9&&j<10)
{
if(i==1&&opera[1][0]==15&&j>8) goto pp;
if(j==2&&opera[i][1]==0&&opera[i][10]==0)
opera[i][1]=save; // 防止小数位不在时首位为零
else{
opera[i][j]=save;opera[i][11]=j;j++;}
if(i==0) // 显示
dis_cdata(0x90);
else
dis_cdata(0x88);
}
else if(save==10&&j<10)
{
if(opera[i][10]==0) // 小数点空时保存
{
if(opera[i][11]==0) {opera[i][10]=2;j++;}
else opera[i][10]=j;
}
}
else if(save==16)
{ // 删除数据
removal_data(i,0);j=1;
if(i!=0){i--;j=10;}
}
else if(i==1&&opera[1][11]!=0&&save>11&&save<16)
{ save1=save;break; } // 连续计算时保存运算符
else if(save==11&&opera[1][11]==0) continue;// 操作数1为0时不理会
else if(save==11&&opera[1][11]!=0) break;
else if((i==0||i==1&&j==1)&&save>11&&save<16){i=0; break;}
// 当操作数0由运算符结束输入,再按符号键更改
else continue;
}
if(opera[i][10]>opera[i][11]||opera[i][10]==0)
opera[i][10]=opera[i][11]+1; // 整数时小数位保存到最后
while(opera[i][11]>=opera[i][10]&&opera[i][opera[i][11]]==0)
opera[i][11]--; // 去除小数点后多余的0
if(i==0)
{
opera[1][0]=save; // 保存运算符并显示
display_cnasc(0x88,1,tool_cal[save-12]);
}
if(opera[0][11]==0) display_cnasc(0x95,1," 0");
j=1;
while(j<=opera[i][11]&&opera[i][j]==0) j++;//判断是否操作数是否全为0
j--;
if(j==opera[i][11]) opera[i][11]=0;
j=1;
}
return 1;
}
/****************************************************************************************
功能: 乘法运算
描述: 结果由右到左保存
参数: i , j , opera[i][j],p,q,r,k,save1
返回值：1(成功),0(结果位0),-1(溢出)
/****************************************************************************************/
char multiplication()
{
uchar p,q,r,k,save1=0; // p指向操作数0 ,q指向操作数1,r指向结果
if(opera[0][11]==0||opera[1][11]==0) return 0;
resu[10]=opera[0][11]+opera[1][11]-opera[0][10]-opera[1][10]+2; // RESU记录小数点后的位数
q=opera[1][11]; // 记录操1的位数
r=9;
opera[1][11]=1;
k=1;
while(opera[1][k]==0) {opera[1][11]=opera[1][11]+1;k++;} // 去除前端的0
k=1;
while(opera[0][k]==0) k++; // 去除前端的0
resu[11]=9;
for(resu[0]=9;q>=opera[1][11];q--,resu[0]--)
{
if(opera[1][q]==0) continue; // 操1此位数为0时直接比较
for(p=opera[0][11],r=resu[0];p>=k;p--)
{
save1=opera[0][p]*opera[1][q]; // 将相乘后的数保存
resu[r]+=(save1%10);//将缓存中的数取余后加到结果中R指向的位
save1/=10;
save1=save1+(resu[r]/10); // 保存进位的数
resu[r]%=10; // 重新写入
if(r==1) //结果有溢出时移位
{
if(save1==0&&p==k) break; // 计算到最后位且没进位跳出
else if(resu[10]>0) // 要求有小数存在
{
for(r=9;r>1;r--) resu[r]=resu[r-1];
r=1;
resu[r]=save1;
resu[11]=1;
resu[10]--;
resu[0]++;
}
else return -1; // 否则溢出
}
if(r>1&&(r-1)<resu[11]) // 保存结果位的最高位
{
if(save1!=0) resu[11]=r-1;
else resu[11]=r;
}
if(r>1){ r--;resu[r]+=save1;}// 当R为1时只需要移位记录结果
}
}
while(resu[resu[11]]==0) resu[11]++; // 去除前端的0
resu[0]=opera[0][0]; // 保存符号位
removal_data(0,1); // 清数据不清显示
if(resu[10]>8) //如果小数点后的数有9 位或以上时，需后移到使小数点放到2的位置
{
save1=resu[10]-10+resu[11]; // 记录后移位数
if(save1>7) return 0; //当后移的数大于有效数字的位数时结果为0
else // 否则按需移位
{
for(p=save1+2,r=resu[11];p<10;p++,r++) opera[0][p]=resu[r];
opera[0][10]=2;opera[0][11]=9;opera[0][0]=resu[0];
} // 因有效数小于小数点后的数,所以首位为0
}
else //如果小数点后的数在8位以内时分两种情况
{
opera[0][0]=resu[0];
save1=10-resu[11]; // 记录有效位数
if(resu[10]>=save1) // 小数的在有效数字的左边
{
for(p=resu[10]+1,r=9;r>=resu[11];p--,r--)
opera[0][p]=resu[r]; // 从小数点的最后一位开始
opera[0][10]=2;opera[0][11]=resu[10]+1;
}
else // 小数点在有效数字内
{
for(p=1,r=resu[11];r<10;p++,r++) opera[0][p]=resu[r];
opera[0][11]=10-resu[11];
if(resu[10]==0) opera[0][10]=opera[0][11]+1;
else opera[0][10]=opera[0][11]-resu[10]+1;
}
}
while(opera[0][11]>=opera[0][10]&&opera[0][opera[0][11]]==0)
opera[0][11]--; // 去除小数点后多余的0
return 1;
}
/****************************************************************************************
功能: 除法运算
描述: 结果由左到右保存
参数: i , j , opera[i][j]
p,q,r, remainde, divisor, decimal
返回值：1(成功),0(结果位0),-1(溢出)
*****************************************************************************************/
char divider()
{
unsigned long int divisor=0,remainder=0;
uchar p,q,r;
char decimal=0;
if(opera[1][11]==0) return -1;
if(opera[0][11]==0) return 0;
for(r=1;r<12;r++) // 判断两数是否相等
{
if(opera[0][r]!=opera[1][r]) break;
}
if(r==12)
{
p=opera[0][0];
removal_data(0,1);
opera[0][0]=r;
opera[0][1]=1;
opera[0][10]=2;
opera[0][11]=1;
return 1;
}
decimal=(opera[0][11]-opera[0][10])-(opera[1][11]-opera[1][10]);
// 记录两操作数小数点后位数的差
if(decimal>0) // 若操0大于操1时重新记录小数点的位置
{
opera[0][10]=opera[0][11]-decimal+1;
resu[10]=opera[0][10];
}
else // 否则小数点后没有数，记录有效数的位数
{
opera[0][11]-=decimal;
opera[0][10]=opera[0][11]+1;
resu[10]=opera[0][10];
}
q=1;
divisor=0;
while(q<=opera[1][11]) // 将操1的数整形化
{
divisor=divisor*10+opera[1][q];q++;
}
if(divisor==1)
{
if(resu[10]>10) return -1;
else return 1;
}
r=1;p=1;
remainder=(unsigned long int)opera[0][1]; // 先对余数寄存器附初值
do
{
if(r>9) // 结果位已经到达最后1位
{
if(resu[1]==0&&resu[10]!=2) // 判断是否有得移位
{
for(r=1;r<9;r++) resu[r]=resu[r+1];
resu[9]=0;
if(resu[10]!=0) resu[10]--;
r=9;
}
else if(p>=opera[0][11]||p>=opera[0][10]) break; // 如果计算到最后一位，或者有小数点存在时结束
else return -1; // 否则错误
}
resu[r]=(uchar)(remainder/divisor); // 保存结果
remainder=(remainder%divisor); // 重新写入余数
p++;r++;
if(p>opera[0][11]&&remainder==0) break; // 除尽后跳出
else if(p<=opera[0][11]&&p<10) // 余数*10后加后一位
{remainder=remainder*10+opera[0][p];}
else remainder=remainder*10; //超出后余数*10
}while(1);
resu[11]=r-1;
resu[0]=opera[0][0];
removal_data(0,1);
r=1;
while(resu[r]==0&&resu[10]!=(r+1)&&r<resu[11]) r++;
//去除结果前端的0
if(r==resu[11]) return 0;
resu[10]=resu[10]-r+1;
p=1;
while(r<=resu[11]){opera[0][p]=resu[r];r++;p++;}
opera[0][0]=resu[0];opera[0][10]=resu[10];opera[0][11]=p-1;
while(opera[0][11]>=opera[0][10]&&opera[0][opera[0][11]]==0)
opera[0][11]--;
return 1;
}
/****************************************************************************************
功能: 加法运算
描述: 以小数点位中心两边相加
参数: i , j , opera[i][j],p,q,r
返回值：1(成功),0(结果位0),-1(溢出)
/****************************************************************************************/
char adder()
{
uchar p,q,r;
if(opera[0][11]==0&&opera[1][11]==0) return 0;
else if(opera[0][11]==0)
{for(q=0;q<12;q++) opera[0][q]=opera[1][q];return 1;}
else if(opera[1][11]==0) return 1;
else
{
p=opera[0][10]-1;
q=opera[1][10]-1;
p>q?(r=p):(r=q);
resu[10]=r+1; // 小数点位保存
resu[0]=opera[0][0]; // 保存符号位
while(r>0) // 将小数点前的数相应相加后放到结果中
{
if(p>0&&q>0){resu[r]=opera[0][p]+opera[1][q];p--;q--;}
else if(p>0&&q==0){resu[r]=opera[0][p];p--;}
else {resu[r]=opera[1][q];q--;}
r--;
}
r=resu[10];
p=opera[0][10];
q=opera[1][10];
while(r<10) // 将小数点后的数放到结果中
{
if(p>opera[0][11]&&q>opera[1][11]) break;
else if(p<=opera[0][11]&&q<=opera[1][11])
{resu[r]=opera[0][p]+opera[1][q];p++;q++;}
else if(p<=opera[0][11]&&q>opera[1][11])
{resu[r]=opera[0][p];p++;}
else {resu[r]=opera[1][q];q++;}
r++;
}
r--;
resu[11]=r;
p=0;
while(r>0) // 由右到左将大于9的数进位
{
resu[r]+=p; // p为进位标记
p=0;
if(resu[r]>9) {resu[r]-=10;p=1;}
r--;
}
if(p==1) // 溢出移位
{
if(resu[10]==10) return -1;
else {
for(r=9;r>1;r--) resu[r]=resu[r-1];
resu[1]=1;resu[10]++;}
}
removal_data(0,1);
r=0;
while(r<12){opera[0][r]=resu[r];r++;}
while(opera[0][11]>=opera[0][10]&&opera[0][opera[0][11]]==0)
opera[0][11]--;
return 1;
}
}
/****************************************************************************************
功能: 减法运算
描述: 先比较两操作数的大小用one ,two互换
参数: i , j , opera[i][j],p,q,r，one，two
返回值：1(成功),0(结果位0),-1(溢出)
/****************************************************************************************/
char subtraction()
{
uchar p,q,r,one,two;
if(opera[0][11]==0&&opera[1][11]==0) return 0;
else if(opera[0][11]==0)
{
for(q=1;q<12;q++)
opera[0][q]=opera[1][q];
opera[0][0]=!opera[0][0];return 1;
}
else if(opera[1][11]==0) return 1;
else
{ // 比较大小(大放到one)
if(opera[0][10]>opera[1][10]){one=0;two=1;}
else if(opera[1][10]>opera[0][10]) {one=1;two=0;}
else
{
r=1;
while(r<10&&opera[0][r]==opera[1][r]) r++;
if(r==10) {removal_data(0,1);return 0;}
opera[0][r]>opera[1][r]?(one=0,two=1):(one=1,two=0);
}
p=opera[one][10]-1;
q=opera[two][10]-1;
r=p; // 保存小数点前的数
resu[10]=r+1; // 保存小数点位
resu[0]=0; // 用作借位标记
while(r>0) // 小数点前相减
{
if(p>0&&q>0)
{
opera[two][q]+=resu[0];
resu[0]=0;
if(opera[one][p]>=opera[two][q])
resu[r]=opera[one][p]-opera[two][q];
else
{
resu[0]=1;
resu[r]=10+opera[one][p]-opera[two][q];
}
p--;q--;
}
else
{
if(opera[one][p]<resu[0])
{resu[r]=10+opera[one][p]-resu[0];}
else
{resu[r]=opera[one][p]-resu[0];resu[0]=0;p--;}
}
r--;
}
r=resu[10];
p=opera[one][10];
q=opera[two][10];
while(r<10) // 将小数点后的数放到结果中
{
if(p>opera[one][11]&&q>opera[two][11]) break;
else if(p<=opera[one][11]&&q<=opera[two][11])
{
if(opera[one][p]>=opera[two][q]) resu[r]=opera[one][p]-opera[two][q];
else
{
resu[r]=10+opera[one][p]-opera[two][q];
resu[0]=r;
for(r-=1;r>0;r--) // 向前借位
{
if(resu[r]==0) resu[r]=9;
else{resu[r]-=1;break;}
}
r=resu[0];
}
p++;q++;
}
else if(p<=opera[one][11]&&q>opera[two][11])
{resu[r]=opera[one][p];p++;}
else
{
resu[r]=10-opera[two][q];
resu[0]=r;
for(r-=1;r>0;r--)
{
if(resu[r]==0) resu[r]=9;
else{ resu[r]-=1;break;}
}
r=resu[0];
q++;
}
if(r==9) // 结果溢出移位
{
if(resu[1]==0&&resu[10]!=2)
{
for(r=1;r<9;r++) resu[r]=resu[r+1];
resu[10]--;resu[9]=0;r=8;
}
}
r++;
}
r--;
resu[11]=r;
if(one==0)resu[0]=opera[0][0]; // 符号位写入
else resu[0]=!opera[0][0];
removal_data(0,1);
r=1;
while(resu[r]==0&&resu[10]!=(r+1)) r++; // 去除前端0
resu[10]=resu[10]-r+1; // 重新写入小数点
p=1;
while(r<=resu[11]){opera[0][p]=resu[r];r++;p++;}
opera[0][0]=resu[0];opera[0][10]=resu[10];opera[0][11]=p-1;
while(opera[0][11]>=opera[0][10]&&opera[0][opera[0][11]]==0) opera[0][11]--;
return 1;
}
}
/****************************************************************************************
功能: 计算器主函数
描述: 根据符号位,运算符调用函数
参数: state,save
返回值：无
****************************************************************************************/
void calculator(void)
{
char data state;
uchar data save;
save1=0;
dis_title_e();
display_cnasc(0x82,3,tool_menu[0]);
display_cnasc(0x96,2,"等于");
display_cnasc(0x8e,2,"删除");
display_cnasc(0x9e,2,"退出");
removal_data(2,0); // 0为清除显示
removal_data(0,0);
i=0;j=1;
while(1)
{
cal_run=0;
state=input_data();
if(state==1) // 根据opera[1][0]的数值调用程序
{
if(opera[1][0]==12&&opera[0][0]==0||opera[1][0]==13&&opera[0][0]==1)
state=adder();
else if(opera[1][0]==12&&opera[0][0]==1||opera[1][0]==13&&opera[0][0]==0)
state=subtraction();
else if(opera[1][0]==14) state=multiplication();
else state=divider();
}
if(state==0) return;
i=0;j=1;
cal_run=1;
switch(state)
{
case -1: // 结果溢出
removal_data(2,0);
removal_data(0,0);
display_cnasc(0x8a,3,"溢出!!");
save1=0;
break;
case 0: // 结果为零
if(save1==0)
{
removal_data(2,1);
removal_data(0,1);
display_cnasc(0x98,1,"= ");
display_cnasc(0x9d,1," 0");
}
break; // 结果显示
case 1:
if(save1==0)
{
cal_run=1;
display_cnasc(0x98,1,"= ");
dis_cdata(0x98);
}
break;
}
if(save1==0) save=gotkey(); // save1记录连续计算符
cal_run=0;
if((save>11&&save<16&&state==1)||save1!=0)
{
removal_data(2,0);
removal_data(1,0);
display_cnasc(0x90,6," ");
if(opera[0][11]==0) display_cnasc(0x95,1," 0");
else dis_cdata(0x90);
if(save1!=0)save=save1;
save1=0;
display_cnasc(0x88,1,tool_cal[save-12]);
opera[1][0]=save;
i=1;j=1;
}
else if(save>=0&&save<10&&state==1)
{
removal_data(2,0);
removal_data(0,0);
opera[0][1]=save;
opera[0][11]++;
dis_cdata(0x90);
i=0;j=2;
}
else if(save==10)
{
removal_data(2,0);
removal_data(0,0);
opera[i][10]=2;
opera[i][11]=1;
j=2;
}
else
{
removal_data(2,0);
removal_data(0,0);
}
}
}
/*=====================================================================================
函数名称：温度功能
功能描述：连续检查温度
全局变量：temprun oth_run als_temp adju_si
参数说明：见函数
返回说明：无
设计人：JZHG
版本：1.0
说明：
======================================================================================*/
/*温度显示*/
uchar temp_func_dis(void)
{
uchar save[2],k;
clear_dis();
dis_title_e();
display_cnasc(0x82,3,"温度计");
display_cnasc(0x98,3,"设定");
display_cnasc(0x9e,3,"退出");
display_cnasc(0x8e,1," \x1f");
num2_asc_dis(10,0x85);
temprun=1;
while(1)
{
if(ds18b20)
{
if(temp.t_data[0]>99) // 温度值大于99时
{
save[0]=temp.t_data[0]/100;
save[1]=(temp.t_data[0]/10)%10;
num2_asc_dis(save[0],0x80);
num2_asc_dis(save[1],0x81);
save[0]=char_num[temp.t_data[0]%10];
num2_asc_dis(save[0],0x82);
}
else // 温度小于100
{
con_disp(0x00,0x00,0x80,0x90,1,16);
con_disp(0x00,0x00,0x88,0x90,1,16);
if(temp_pn) con_disp(0x3f,0xfc,0x80,0x9d,1,3);
else con_disp(0x00,0x00,0x80,0x9d,1,3);
save[0]=temp.t_data[0]/10;
save[1]=temp.t_data[0]%10;
num2_asc_dis(save[0],0x81);
num2_asc_dis(save[1],0x82);
}
save[0]='.';
save[1]=char_num[temp.t_data[1]/10];
display_cnasc(0x8b,1,save);
save[0]=char_num[temp.t_data[1]%10];
if(save[0]=='1') save[1]='2'; // 补偿精度
else if(save[0]=='7') save[1]='5';
else if(save[0]=='8'||save[0]=='1') save[1]='7';
else save[1]='0';
display_cnasc(0x8c,1,save);
}
else
{
clear_dis();
display_cnasc(0x92,4,"没有发现");
display_cnasc(0x8c,4,"温感器！");
delay_pw();
delay_pw();
delay_pw();
temprun=0;
return 0;
}
k=gotkey();
if(k==2) // 进入设置菜单
{
display_cnasc(0x8e,1," \x04");
delay(35000);
display_cnasc(0x8e,1," \x1e");
display_cnasc(0x9a,4,"\x11 (ok) \x10");
return 1;
}
}
}
/*警报温度设置*/
uchar temp_func_set(void)
{
uchar save[2];
temprun=0;
oth_run=0;
rds1302_data();
while(1)
{
if(oth_run)
{
con_disp (0x00,0x00,0x88,0x90,2,16);
con_disp (0xff,0xff,0x8e,0x90,2,16);
}
else
{
con_disp (0xff,0xff,0x88,0x90,2,16);
con_disp (0x00,0x00,0x8e,0x90,2,16);
}
save[0]=gotkey();
if(save[0]==1||save[0]==3) oth_run=!oth_run;
if(save[0]==5) return 1;
if(save[0]==11)
{
if(oth_run) return 0;
else
{
clear_dis();
dis_title_e();
save[1]=save[0]=0;
oth_run=0;
dis_title_e();
display_cnasc(0x82,3,"设定");
display_cnasc(0x90,5,"警报温度：");
display_cnasc(0x88,7,"高于【】℃");
display_cnasc(0x98,8,"低于【】℃ \x10");
while(1)
{
if(save[1]==2) con_disp(0x00,0x00,index_temp_set[save[1]].lnum,index_temp_set[save[1]].rnum,2,13);
else con_disp(0x00,0x00,index_temp_set[save[1]].lnum,index_temp_set[save[1]].rnum,2,13);
if(save[0]==2) con_disp(0x0f,0xff,index_temp_set[save[0]].lnum,index_temp_set[save[0]].rnum,1,13);
else con_disp(0xff,0xff,index_temp_set[save[0]].lnum,index_temp_set[save[0]].rnum,2,13);
save[1]=save[0];
adju_si=0;
oth_run=0;
while(1)
{
for(i=0;i<2;i++)
{
j=0x8b+i*16;
if(als_temp[i]==255) display_cnasc(j,2," off"); // 255值为关闭值
else
{
save1=save[1];
if(als_temp[i]>127) // 当数值大于127时温度值为负数
{
display_cnasc(j,1,"- ");
save[0]=char_num[(als_temp[i]-128)/10];
save[1]=char_num[(als_temp[i]-128)%10];
display_cnasc(j+1,1,save);
}
else
{
save[0]=' ';
save[1]=char_num[als_temp[i]/100];
if(save[1]=='0') save[1]=' ';
display_cnasc(j,1,save);
save[0]=char_num[als_temp[i]/10%10];
save[1]=char_num[als_temp[i]%10];
display_cnasc(j+1,1,save);
}
save[1]=save1;
}
}
save[0]=gotkey();
do // 输入符号等待数值输入或下一位
{
if(save[0]==13){ oth_run=1;display_cnasc(0x8b+save[1]*16,2,"- ");}
else if(save[0]==12){ oth_run=0;display_cnasc(0x8b+save[1]*16,2," ");}
else break;
save[0]=gotkey();
if(save[0]>=0&&save[0]<10||save[0]==11) break;
}while(1);
if(save[0]==14){ als_temp[save[1]]=255;} // 乘号直接将警报温度关闭
if(save[0]>=0&&save[0]<10&&save[1]<2)
{
if(adju_si)
{
adju_si=0;
if(oth_run) als_temp[save[1]]&=0x7f; // 消去符号位
if(als_temp[save[1]]>24&&!oth_run) als_temp[save[1]]=240;
else als_temp[save[1]]=als_temp[save[1]]*10+save[0];
if(oth_run&&als_temp[save[1]]>50) als_temp[save[1]]=50;
if(!oth_run&&als_temp[save[1]]>120) als_temp[save[1]]=120;
if(!oth_run&&als_temp[save[1]]<100) adju_si=1; // 根据数值打开连写
if(oth_run&&als_temp[save[1]]<10) adju_si=1;
}
else
{
als_temp[save[1]]=save[0];
adju_si=1;
}
if(oth_run) als_temp[save[1]]=als_temp[save[1]]|0x80; // 写入符号
else als_temp[save[1]]=als_temp[save[1]]&0x7f;
}
if(save[0]==11)
{
if(als_temp[1]!=255&&als_temp[0]!=255) // 上下限温度调整
{
if(save[1]==0&&als_temp[0]<als_temp[1]){als_temp[0]=als_temp[1];}
if(save[1]==1&&als_temp[1]>als_temp[0]){als_temp[1]=als_temp[0];}
}
save[0]=save[1]+1;adju_si=0;break;}
if(save[0]==10&&save[1]!=0) {save[0]=save[1]-1;adju_si=0;break;}
}
oth_run=0;
if(save[0]==3&&save[1]==2) break;
}
save_y_or_n();
if(oth_run)
{
wds1302_data(d02_temp,als_temp[0]);
wds1302_data(d02_temp+2,als_temp[1]);
}
return 1;
}
}
}
}
/*温度计主函数*/
void temp_func(void)
{
uchar t;
while(1)
{
oth_run=1;
t=temp_func_dis();
if(t==1)
{
t=temp_func_set();
if(t==0) return;
}
else return;
}
}
/*=====================================================================================
函数名称：闹铃功能
功能描述：设定闹铃
全局变量：alarm_time adju_si
参数说明：见函数
返回说明：无
设计人：JZHG
版本：1.0
说明：
======================================================================================*/
void alarm_func(void)
{
uchar save[2],a,d;
clear_dis();
dis_title_e();
display_cnasc(0x82,3,"闹钟");
display_cnasc(0x91,6,"状态：\x11 \x10");
display_cnasc(0x89,3,"闹铃：");
display_cnasc(0x9f,1,"→");
display_cnasc(0x90,1,"『");
display_cnasc(0x8f,1,"』");
adju_si=0;
a=0;d=0;
save[0]=char_num[alarm_time[0]>>4];
save[1]=char_num[alarm_time[0]&0x0f];
display_cnasc(0x8c,1,save);
display_cnasc(0x8d,1,": ");
save[0]=char_num[alarm_time[1]>>4];
save[1]=char_num[alarm_time[1]&0x0f];
display_cnasc(0x8e,1,save);
do
{
if(a==0)
{
display_cnasc(0x95,1,alm_sign[alm]);
display_cnasc(0x94,1,"\x11 ");
display_cnasc(0x96,1," \x10");
con_disp(0x00,0x00,index_alm[d-1].lnum,index_alm[d-1].rnum,1,14);
}
if(a>0&&a<4)
{
if(d==0)
{
display_cnasc(0x94,1," ");
display_cnasc(0x96,1," ");
}
else
con_disp(0x00,0x00,index_alm[d-1].lnum,index_alm[d-1].rnum,1,14);
con_disp(0xff,0xff,index_alm[a-1].lnum,index_alm[a-1].rnum,1,14);
}
d=a;
while(1)
{
a=gotkey();
if((a==1||a==3)&&d==0)
{
alm=!alm;
if(a==1) display_cnasc(0x94,1,"\x09 ");
else display_cnasc(0x96,1," \x09");
delay(35000);
if(a==1) display_cnasc(0x94,1,"\x11 ");
else display_cnasc(0x96,1," \x10");
display_cnasc(0x95,1,alm_sign[alm]);
}
if(d>0&&d<3&&a>=0&&a<10)
{
if(adju_si)
{
alarm_time[d-1]<<=4;alarm_time[d-1]+=a;
if(d==1&&alarm_time[0]>0x23) alarm_time[0]=a;
else if(d==2&&alarm_time[1]>0x59) alarm_time[1]=a;
else adju_si=0;
}
else
{
alarm_time[d-1]=a;adju_si=1;
}
save[0]=char_num[alarm_time[d-1]>>4];
save[1]=char_num[alarm_time[d-1]&0x0f];
display_cnasc(0x8c+(d-1)*2,1,save);
}
if(a==11){a=d+1;break;}
if(a==10&&d!=0){a=d-1;break;}
}
adju_si=0;
if(a==4)
{
save_y_or_n();
wds1302_data(d02_signs,signs);
wds1302_data(d02_alm,alarm_time[0]);
wds1302_data(d02_alm+2,alarm_time[1]);
return;
}
}while(1);
}
/*=====================================================================================
函数名称：篮球器功能
功能描述：分数时间 24秒
全局变量：resu opera
参数说明：见函数
返回说明：无
设计人：JZHG
版本：1.0
说明：
======================================================================================*/
/*比赛设置*/
void nba_set(void)
{
uchar nba,save1,key,save[2];
clear_dis();
dis_title_e();
if(resu[7]==1) display_cnasc(0x82,3,"加时");
else
{
display_cnasc(0x82,3,"设定");
opera[0][0]=0;
opera[1][0]=1;
}
resu[6]=0; // 赋初值
resu[0]=1;
resu[1]=4;
resu[2]=12;
resu[3]=0;
resu[4]=24;
display_cnasc(0x90,7,"队1:红队2:白");
display_cnasc(0x88,7,"24秒:Y 节数:4");
display_cnasc(0x98,8,"每节时间: 12分钟");
save1=0;nba=0;
while(1)
{
if(save1==4) display_cnasc(0x9c,1,":");
else display_cnasc(index_nba[save1],1," ");
if(nba==4) display_cnasc(0x9c,1,":\x10");
else display_cnasc(index_nba[nba],1,"\x11 ");
save1=nba;
key=gotkey();
if(key==1||key==3)
{
switch(nba) // 导航更改数据
{
case 0:
case 1:
if(key==1){if(opera[nba][0]>0) opera[nba][0]--;
else opera[nba][0]=7;}
if(key==3){if(opera[nba][0]<7) opera[nba][0]++;
else opera[nba][0]=0;}
display_cnasc(index_nba[nba]-1,1,nba_oppo[opera[nba][0]]);
break;
case 2:
if(resu[0]>0) resu[0]=0;
else resu[0]=1;
if(resu[0]>0) display_cnasc(0x8a,1,":Y");
else display_cnasc(0x8a,1,":N");
break;
case 3:
if(key==1){if(resu[1]>1) resu[1]--;
else resu[1]=4;}
if(key==3){if(resu[1]<4) resu[1]++;
else resu[1]=1;}
save[0]=':';
save[1]=char_num[resu[1]];
display_cnasc(0x8e,1,save);
break;
case 4:
if(key==1){if(resu[2]>0) resu[2]--;
else resu[2]=60;}
if(key==3){if(resu[2]<60) resu[2]++;
else resu[2]=0;}
save[0]=char_num[resu[2]/10];
save[1]=char_num[resu[2]%10];
display_cnasc(0x9d,1,save);
resu[5]=resu[2];
break;
}
}
if(key==11)
{
nba++; if(nba==5) return;
}
if(key==10&&nba!=0) nba--;
}
}
/*界面其他元素*/
void nba_oth_dis(void)
{
uchar save[2];
if(resu[7]==1) display_cnasc(0x80,5,"加时时间：");
else display_cnasc(0x80,5,"比赛时间：");
display_cnasc(0x98,1,nba_oppo[opera[0][0]]);
display_cnasc(0x9e,1,nba_oppo[opera[1][0]]);
display_cnasc(0x99,1,"队");
display_cnasc(0x9f,1,"队");
save[0]='0';
save[1]=char_num[resu[6]+1];
display_cnasc(0x9b,1,save);
display_cnasc(0x9c,1,"st");
con_disp(0xff,0xff,0x83,0x90,2,1); // 画正方框
con_disp(0xff,0xff,0x8b,0x8f,2,1);
con_disp(0x80,0x00,0x83,0x91,1,15);
con_disp(0x00,0x01,0x84,0x91,1,15);
con_disp(0x80,0x00,0x8b,0x80,1,15);
con_disp(0x00,0x01,0x8c,0x80,1,15);
nba_dis_time();
if(resu[0]==0) display_cnasc(0x93,2,"\x07--\x07");
display_cnasc(0x8b,2," S! ");
}
/*篮球器主函数*/
void nba_timer(void)
{
uchar save,key,nba=0;
als=di0=1;alm=keb=di1=oth_run=0;
time_init();
display_cnasc(0x82,3,"篮球器");
dis_title_e();
removal_data(0,1);
while(1) // 使用说明
{
display_cnasc(0x90,8,timer_tips[nba]);
display_cnasc(0x88,8,timer_tips[nba+1]);
display_cnasc(0x98,8,timer_tips[nba+2]);
key=gotkey();
if(key==11)
{
nba+=3;
if(nba>9) break;
}
if(key==10)
{
if(nba>0) nba-=3 ;
}
}
nn:
nba_set();
clear_dis();
nba_oth_dis();
nba_tim=1;
while(1)
{
for(save=0x80,nba=0;nba<2;nba++)
{
if(opera[nba][1]>99) // 分数显示
{
num2_asc_dis(opera[nba][1]/100,save);
num2_asc_dis(opera[nba][1]/10%10,save+1);
num2_asc_dis(opera[nba][1]%10,save+2);
}
else
{
num2_asc_dis(opera[nba][1]/10,save);
num2_asc_dis(opera[nba][1]%10,save+1);
}
if(opera[1][1]>99) save=0x85;
else save=0x86;
}
do
{
key=gotkey();
ss:
switch(key)
{
case 12:
case 13:
if(key==12)
{if(opera[0][1]<250) opera[0][1]++;}
else
{if(opera[0][1]>0) opera[0][1]--;}
save=110;
break;
case 14:
case 15:
if(key==14)
{if(opera[1][1]<250) opera[1][1]++;}
else
{if(opera[1][1]>0) opera[1][1]--;}
save=110;
break;
case 7:
TR1=TR0=EA=0;
if((++resu[3])>59)
{
resu[3]=0;
if((++resu[2])>59)
{
resu[3]=0;
if(++resu[2]>60) resu[2]=0;
}
}
if(resu[4]<24) resu[4]++;
nba_dis_time();
break;
case 8:
if(resu[0]==1)
{
TL1=(time_count&0x00FF);
TH1=(time_count>>8);
resu[4]=24; nba_dis_time();
TR0=TR1=EA=1;
}
break;
case 9:
if(resu[2]==0&&resu[3]==0)
{
resu[2]=resu[5];resu[4]=24;
if(resu[6]==resu[1])
{ // 判断比分进行加时赛
if(opera[0][1]==opera[1][1]){nba_tim=0;resu[7]=1; goto nn;}
while(gotkey()!=10); // 否则只能退出
signs=r1302(d02_signs+1);
nba_tim=0;
return;
}
else nba_oth_dis();
break;
}
if(EA) {TR0=TR1=EA=0;break;}
if(!EA&resu[4]!=0){ EA=TR0=1;if(resu[0]==1) TR1=1;}
break;
case 10:
case 11:
if(!EA) // 暂停状态下 ok键两次返回时钟界面
{ // ./s 键两次退出
delay(6000);
save=gotkey();
if(save==key)
{
if(key==11)
{
clear_dis();oth_run=1;
rds1302_time();
init_d2=1;
dis_mode2();
init_d2=0;
while(gotkey()!=11);
oth_run=0;
save=110;
clear_dis();
nba_oth_dis();
}
else{ signs=r1302(d02_signs+1); nba_tim=0;return;}
}
else{ key=save;goto ss;}
}
break;
}
if(save==110) break;
}while(1);
}
}
/*=====================================================================================
函数名称：设置功能
功能描述：系统状态设置
全局变量：signs
参数说明：见函数
返回说明：无
设计人：JZHG
版本：1.0
说明：
======================================================================================*/
/*设置调整内容参数格式：选中设置项，设置项子值*/
uchar set_dis(uchar menu,uchar sub)
{
uchar save;
con_disp(0xff,0xff,0x8e,0x80,2,16);
con_disp(0x00,0x00,0x8a,0x80,4,16);
display_cnasc(0x96,1,"\x1e ");
display_cnasc(0x9e,1,"\x1f ");
display_cnasc(0x92,1," ");
display_cnasc(0x9a,1," ");
display_cnasc(0x8d,1,"\x11 ");
display_cnasc(0x8a,1," ");
while(1)
{
if(menu<2)
display_cnasc(0x8e,2,set_bl_dm[menu][sub]);
else
display_cnasc(0x8e,2,set_mka[menu-2][sub]);
save=gotkey();
if(save==5)
{
key_dis(0x96);
if(sub==0&&menu<2) sub=2;
else if(sub==0&&menu>1) sub=1;
else sub--;
}
if(save==2)
{
key_dis(0x9e);
if(sub==2&&menu<2) sub=0;
else if(sub==1&&menu>1) sub=0;
else sub++;
}
if(save==1||save==11)
{
display_cnasc(0x8d,1,"\x04 ");
delay(30000);
con_disp(0x00,0x00,0x8e,0x80,2,16);
con_disp(0xff,0xff,0x8a,0x80,4,16);
display_cnasc(0x92,1,"\x1e ");
display_cnasc(0x9a,1,"\x1f ");
display_cnasc(0x96,1," ");
display_cnasc(0x9e,1," ");
display_cnasc(0x8a,1,"【");
display_cnasc(0x8d,3,"】\x10 \x04 ");
return(sub); // 返回设置值
}
}
}
/*设置调整*/
void set_func(void)
{
uchar d,key,save;
display_cnasc(0x81,2,"设置");
dis_title();
display_cnasc(0x88,8,selected[1]);
con_disp(0xff,0xff,0x8a,0x80,4,16);
save=d=0;
do
{
display_cnasc(0x93,2,set_menu[index_s[save].lnum]);
display_cnasc(0x8b,2,set_menu[save]);
display_cnasc(0x9b,2,set_menu[index_s[save].rnum]);
d=save;
while(1)
{
key=gotkey();
if(key==11||key==3){ enter_dis();break;}
if(key==5){save=index_s[d].lnum;key_dis(0x92); break;}
if(key==2){save=index_s[d].rnum;key_dis(0x9a); break;}
if(key==1){ wds1302_data(d02_signs,signs); return;}
}
if(key==11||key==3)
{
save=0;
for(key=0;key<2;key++) // 进行两次比较首次为现时值其次为设定置更改
{
…………余下代码请下载附件…………

复制代码

ID:82738 · 发表于 2021-8-29 22:56

menu_index code index_m[6]={{3,5,1},{4,0,2},{5,1,3},{0,2,4},{1,3,5},{2,4,0}}; // 菜单导航，数组是怎么理解的，谢谢请教

ID:857072 · 发表于 2021-8-30 00:55

这么长我啥时候才啃的完啊。。。。

帐号		自动登录	找回密码
密码			立即注册

12864图文菜单 时间 温度控制系统（128*64LCD+ds1302+ds18b20）

12864图文菜单时间温度控制系统（128*64LCD+ds1302+ds18b20）