前段时间师兄拜托写一个单片机代码，由于之前没整过，在这记录一下。也希望可以帮助到正在学这个的朋友们.stm32F4并不支持自动生成正弦波，事先在正弦波上找500个点存在一个数组里，然后当每一个时钟到来的时候，dac就会输出电压值。
void sin_Generation(void) {u16 n;for(n=0;n<tableSize;n++) {sinTable[n] = (sin(2*PI*n/tableSize)+1)*2047;}
经过线性转换后，数字输入会转换为 0 到 VREF+ 之间的输出电压。各 DAC 通道引脚的模拟输出电压通过以下公式确定：
DACoutput =Vref*dor/4095
接下来就是定时器和GPIO的配置，以及为了避免占用CPU的dma操作
void TIM6_Configuration(void)
{
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM6, ENABLE);
TIM_PrescalerConfig(TIM6, 83, TIM_PSCReloadMode_Update);
TIM_SetAutoreload(TIM6, 70)
TIM_SelectOutputTrigger(TIM6, TIM_TRGOSource_Update)；
TIM_Cmd(TIM6, ENABLE)
}
定时器的arr值和psc值得·设置可以改变输出波形的频率，这里的频率为50hz
void GPIO_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOA, &GPIO_InitStructure);
}
void DAC_DMA_Configuration(void)
{
DAC_InitTypeDef DAC_InitStructure;
DMA_InitTypeDef DMA_InitStructure;
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_DAC, ENABLE);
DAC_InitStructure.DAC_Trigger = DAC_Trigger_T6_TRGO;
DAC_InitStructure.DAC_WaveGeneration = DAC_WaveGeneration_None；
DAC_InitStructure.DAC_OutputBuffer = DAC_OutputBuffer_Disable;
DAC_Init(DAC_Channel_1, &DAC_InitStructure);
DMA_DeInit(DMA1_Stream5);
DMA_InitStructure.DMA_Channel = DMA_Channel_7;
DMA_InitStructure.DMA_PeripheralBaseAddr = DAC_DHR12R1_ADDRESS;
DMA_InitStructure.DMA_Memory0BaseAddr = (uint32_t)&sinTable;
DMA_InitStructure.DMA_BufferSize = tableSize;
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;
DMA_InitStructure.DMA_MemoryDataSize = DMA_PeripheralDataSize_HalfWord;
DMA_InitStructure.DMA_DIR = DMA_DIR_MemoryToPeripheral;
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_InitStructure.DMA_FIFOMode = DMA_FIFOMode_Disable;
DMA_InitStructure.DMA_FIFOThreshold = DMA_FIFOThreshold_HalfFull;
DMA_InitStructure.DMA_MemoryBurst = DMA_MemoryBurst_Single;
DMA_InitStructure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;
DMA_Init(DMA1_Stream5, &DMA_InitStructure);
DMA_Cmd(DMA1_Stream5, ENABLE);
DAC_Cmd(DAC_Channel_1, ENABLE);
DAC_DMACmd(DAC_Channel_1, ENABLE);
}
|
QQ好友和群
QQ空间
腾讯微博
腾讯朋友
收藏
淘帖
顶
踩
